Kenmore Refrigerator 106.51189110 (10651189110, 106 51189110) Parts

Graphite spray paint for appliance touch-ups. Covers chips, scratches, and scuffs on dryer drums, washer panels, and exterior surfaces. Restore finish.

Fixes refrigerator freezing up or warm temps caused by ice buildup on evaporator coils. This defrost heater melts frost during defrost cycles.

Screw for control panel.

This slide is the replacement rack glide that helps a rack roll smoothly in and out of the appliance, restoring proper rack movement and preventing scraping or sticking during use. Fits where the factory rack glide has worn or broken. What it does

• Provides a smooth track for a rack to slide in and out without binding
• Replaces cracked, worn or missing glide that causes rubbing or uneven movement
• Helps keep the rack properly aligned during loading and unloading
• Reduces noise and drag from a damaged or missing glide

• One replacement slide/rack glide

• Remove power supply or disconnect appliance before starting any repair
• Access the glide by sliding the rack out and removing any retainer clips or screws as required
• Snap or screw the replacement slide into place and verify smooth rack movement before restoring power
• If other rack parts are damaged, replace them to ensure proper function

This crisper pan is the replacement pan assembly that supports the refrigerator crisper drawer and catches spills to keep the fresh-food compartment clean. It restores a stable base for produce storage and helps contain leaks. What it does:

• Provides a stable bottom for the crisper drawer and stored produce
• Collects spills and liquids to prevent messes from reaching lower compartments
• Replaces cracked, warped, or damaged pans that cause leaks or items to fall through
• Helps the crisper drawer operate smoothly when seated correctly

• Remove all contents and slide out the crisper drawer before replacing the pan
• Inspect mounting rails and seat the pan fully so the drawer rides smoothly
• Handle carefully to avoid damage; if the pan is glass, lift with both hands

Fix water pooling under your refrigerator with a new evaporator drip tray. Collects defrost runoff and prevents leaks. Moderate DIY repair.

This ice door support bracket holds and stabilizes the freezer ice door so it opens and closes smoothly and keeps the ice compartment sealed. Replaces a worn or broken support to restore proper door alignment and operation. What it does:

• Supports the ice door assembly to prevent drooping or misalignment
• Helps ensure the ice door opens and closes smoothly for reliable dispensing
• Reduces rattling or noise from a loose or damaged door support
• Prevents gaps that can lead to frost buildup or ice spillage

• Disconnect power to the appliance before starting any repair
• Remove the ice bin or door panel per service instructions to access the support
• Use common hand tools; handle plastic parts gently to avoid cracking
• Secure all fasteners; test door movement after installation

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Protective cover that shields and organizes refrigerator wire harnesses. Replaces cracked, broken, or missing covers to prevent wire chafing and exposure.

This small metal mounting clip secures the thermal fuse in place to maintain proper thermal contact and stable wiring. It helps keep the fuse positioned so the appliance can monitor temperature reliably and operate safely. What it does:

• Secures the thermal fuse to the appliance housing or duct to prevent movement
• Keeps the fuse in correct contact with temperature-sensing surfaces
• Helps prevent intermittent heating or thermal-sensor misreads caused by a loose fuse
• Useful when replacing a damaged or missing fuse retainer during fuse service

• One thermal fuse mounting clip

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove access panels per your model's service instructions to reach the fuse location
• Install clip in the same orientation as the original; use pliers if needed to seat it firmly
• Inspect the thermal fuse and wiring while installing; replace any damaged components per OEM guidance

Replacement snack pan assembly that installs in the refrigerator compartment to hold small items and snacks. Needed when original is cracked, broken, or missing.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Front cover for refrigerator ice maker assembly. Mounts to inner door panel and conceals ice maker components. Replace if cracked, broken, or missing.

Color: Mist Beige