Kenmore Refrigerator 106.54534400 (10654534400, 106 54534400) Parts

Sealer for refrigerant line insulation.

This air deflector directs chilled air inside the refrigerator's fresh-food compartment to maintain even cooling and proper circulation. It replaces a damaged or missing deflector so cold air reaches interior shelves and drawers. What it does:

• Guides refrigerated air from the evaporator outlet into the fresh-food section for more even temperatures
• Helps prevent warm spots and uneven cooling on shelves and in drawers
• Restores correct airflow after cracking, warping, or breakage
• Can reduce frost buildup caused by improper air direction

• One air deflector

• Disconnect power to the appliance before beginning any work
• Remove interior shelves or drawers as needed for access
• This part typically snaps into place; align tabs and press until secured
• Handle gently to avoid cracking; verify fit and airflow after installation

This is a flat plain washer used to distribute load and space hardware on appliance assemblies. It helps keep bolts and screws seated and reduces wear on mating surfaces for more secure fastener connections. What it does:

• Provides a flat bearing surface to spread clamp load and protect parts from fastener damage
• Maintains proper spacing and alignment for mounted components
• Helps prevent fastener loosening from vibration when used with the correct bolt or screw
• Commonly used on chassis, suspension, and bracket connections

• One plain flat washer

• Disconnect power and water supply before servicing the appliance
• Replace only with the same washer size and thickness as the original for proper fit
• Tighten fasteners to secure but avoid over-torquing which can deform the washer

Secures components in your coffee maker. Replace if broken, loose, or missing to prevent leaks or rattling. Verify fit with your model number.

Frost building up in your freezer? A worn fan scroll gasket lets warm air bypass the evaporator, causing excess frost and poor cooling performance.

Fix frost buildup in your refrigerator with this defrost heater mounting clip. Secures heater to evaporator for consistent defrosting performance.

Mounting screw for various appliances. Replaces lost, stripped, or damaged screws that secure panels, brackets, or internal components. Essential hardware.

10-32 threaded screw secures panels, brackets, and components inside your refrigerator. Replace missing, stripped, or damaged screws to restore fit.

6 - 19 x .250

Secures air duct to housing, maintaining proper airflow alignment. Replace if broken or loose to prevent air leaks. Confirm fit with your model.

This is a replacement wire harness that restores electrical connections between components so your appliance powers and controls operate correctly. It provides the factory-style wiring needed for reliable signal and power routing. What it does

• Carries power and control signals between major components so circuits can operate as intended
• Commonly used when damaged, melted, cut, or corroded wires cause intermittent operation or loss of function
• Can resolve symptoms such as components not receiving power, control buttons or lights not responding, or erratic behavior due to open/shorted wiring
• Matches OEM routing and connector ends to maintain original fit and connections

• One complete wire harness assembly as shown

• Disconnect all power (unplug or shut off breaker) before starting any repair
• Note wire routing and connector locations or take photos before removal to ensure correct reassembly
• Inspect connectors and mounting clips; replace any broken retainers to prevent chafing or strain

Mounting screw for refrigerator ice maker brackets. Replaces broken, stripped, or missing screws that secure the ice maker assembly to the freezer wall.

This is a small replacement screw used to fasten appliance panels and internal components, restoring secure connections and reducing rattles or loose parts. Ideal when original screws are missing or damaged. What it does:

• Secures access panels, mounting brackets, or internal assemblies to prevent vibration and movement
• Helps maintain electrical and mechanical connections by keeping components properly aligned
• Common fix for loose control panels, trim pieces, or internal module attachments

• One replacement screw as shown

• Use the matching driver (Phillips, hex, or Torx) and hand-start the screw to avoid cross-threading
• Tighten until snug; do not over-torque to prevent stripping or cracking surrounding material
• Disconnect power to the appliance before accessing internal parts to avoid injury
• If the original screw is corroded or broken, replace with the same type and length for best fit

Size: 63-1/2 x 35-1/2 x 2-5/8 inch.

Size: 3/16 inch.