Kenmore Refrigerator 106.60239900 (10660239900, 106 60239900) Parts

Exterior door handle for refrigerators. Installs on the front door panel. Replace when cracked, broken, loose, or missing for proper door operation.

Replacement mounting screw for securing panels, brackets, and components in appliances. Needed when original fastener is missing, stripped, or damaged.

Replacement mounting screw for securing panels, brackets, and components in appliances. Needed when original screws are stripped, missing, or damaged.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

Crisper drawer won't adjust humidity? This slide moves the vent door to regulate moisture in your produce bin. Snap-in replacement restores humidity control.

Replace a cracked, broken, or missing hinge cover on your refrigerator. Snaps over the hinge assembly to conceal hardware and restore a clean finish.

This trim tail handle restores the finished edge and secure mounting at the end of a door or trim panel, improving appearance and helping keep the panel seated correctly. Fits where the trim meets the appliance body. What it does:

• Covers and finishes the exposed end of a trim or door panel for a clean, factory look
• Helps hold the trim/door edge in position to reduce rattling or looseness
• Restores proper fit and alignment after damage or wear to the original trim
• Simple replacement that addresses cosmetic defects and loose or misaligned trim

• Disconnect power or unplug the appliance before starting work
• Use basic hand tools; support the door/panel to prevent drops or pinching
• Keep track of fasteners and use the original screws where applicable

Rubber grommet kit that mounts and cushions the compressor. Replace worn, cracked, or damaged grommets to restore proper support and isolation.

Black button plug for refrigerators. Covers and conceals holes or openings in cabinet panels. Replace if cracked, broken, missing, or discolored.

Trim piece that covers and finishes the outer corner where filler panels meet on your refrigerator. Replace if cracked, broken, or missing.

Replaces cracked, loose, or missing door shelf trim on your refrigerator. Restores the finished edge and support for door shelves to keep items secure.

Fix ice maker or water dispenser issues with this valve tube body. Routes water from the main valve to dispenser and ice maker. Stops leaks from damaged tubes.

Replaces the plastic front edge trim on refrigerator door shelves. Needed when the original trim is cracked, chipped, broken, or missing from your shelf.

This is a replacement 1/4-20 threaded screw used to secure appliance components and panels. It restores proper fastening where a matching screw is missing, loose, or stripped and helps stop rattling or misalignment. What it does:

• Secures panels, brackets, and assemblies to maintain proper alignment and reduce vibration
• Replaces missing or damaged fasteners that cause loose or rattling parts
• Works wherever a 1/4-20 threaded screw is specified by the manufacturer
• Simple mechanical fastener—no electrical or calibration changes required

• Disconnect power to the appliance before servicing to avoid injury
• Use the matching driver and thread engagement; do not overtighten to prevent stripping
• Verify screw length and head type match the original before installing
• If threads are damaged, repair or replace the mating component rather than forcing the screw