Kenmore Refrigerator 106.74213402 (10674213402, 106 74213402) Parts

Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.

Replace a cracked, broken, or missing hinge cover on your refrigerator. Snaps over the hinge assembly to conceal hardware and restore a clean finish.

Screw: 8-16 x 3/8 inch.

Size: 8-18 x 1/2 inch.

Replace your burned-out refrigerator light bulb to restore clear visibility inside your appliance. Easy installation when bulb flickers or fails.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

White porcelain touch-up paint for repairing chipped, scratched, or worn surfaces on ranges, ovens, and refrigerators. Restores appearance on exterior panels and trim. 2 oz. can.

Hinge center shim spacer that maintains proper door spacing and alignment. Replace when worn, missing, or cracked to prevent door rubbing and uneven gaps.

Secures water supply hoses to fittings, preventing leaks in ice makers and refrigerators. Replace when rusted, bent, or losing grip. Verify fit.

Refrigerator won't cool or compressor rattles? This sealed system compressor restores cooling. Professional installation required for refrigerant work.

Drier tube for refrigerators. Installs in the sealed refrigeration system to remove moisture. Replace if cracked, corroded, or during compressor repairs.

Fix frost buildup and inconsistent cooling with a new evaporator cover gasket. This seal prevents moisture accumulation at the evaporator compartment.

This air baffle assembly directs airflow inside the dryer to support even drying and proper venting. A direct-fit replacement that restores airflow routing and helps resolve common drying performance issues. What it does:

• Channels heated air from the blower to the drum and exhaust path
• Helps maintain consistent drying by preventing air leakage or misrouting
• Commonly replaced when dryers have reduced drying performance or unusual airflow noise
• Works with the dryer's internal ducting and blower system to preserve vent efficiency

• One air baffle assembly

• Replace only with power disconnected; unplug the dryer or switch off breaker before servicing
• Basic disassembly of the dryer cabinet or front panel may be required; follow manufacturer service instructions
• Inspect adjacent seals, clips, and ducting for wear and replace if damaged

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This mounting cup installs in the freezer liner to create a secure attachment point for the ice maker or its bracket. It helps keep the assembly stable and properly aligned so the ice maker mounts firmly and operates reliably. What it does:

• Provides the receiving anchor for the ice maker/bracket mounting screw
• Helps hold the ice maker level and reduces movement or vibration
• A worn, stripped, or missing cup can prevent the screw from tightening
• Common signs include a loose or sagging ice maker, rattling, or difficulty keeping the ice maker aligned

• 1 mounting cup

• Disconnect power and shut off the water supply before servicing
• Remove the ice maker to access the cup location
• Seat the cup fully into the liner opening, then reinstall the bracket/ice maker and mounting screw
• Do not overtighten; verify the ice maker sits level and clears the fill tube