Kenmore Refrigerator 106.9552410 (1069552410, 106 9552410) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10250570
This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:
- Supports the refrigerator cabinet and helps maintain proper leveling
- Allows the unit to roll for easier cleaning and servicing
- Replaces worn, cracked, or seized rollers and damaged brackets
- Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge
What's included:
- One complete cabinet roller assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
- Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
- After installation, level the refrigerator and verify doors close and seal properly
Do-It-Yourself Stories from Customers like You
The plastic left rear wheel was coming apart and needed replacing Gary H. • San Antonio , TX • June 11, 2016
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The...
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking water filter housing and broken grill cover clips Carl H. • Strongsville , OH • December 04, 2016
Ordered parts, watched the videos on your website. Very simple.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W10136387A
Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.
Do-It-Yourself Stories from Customers like You
Broken part Donna B. • Waterbury , CT • October 28, 2016
Ordered a replacement part from your on line store.
Read more
More
$11.34
- Compare At:
-
$13.49
- You Save:
-
$2.15
Genuine Whirlpool part
By: Whirlpool
Part Number: 4388539
Shelf stud
Do-It-Yourself Stories from Customers like You
Broken shelf stud Richard B. • Ballwin , MO • December 24, 2016
Watched your youtube video which was awesome and then knew how to take it out without breaking the side of fridge it went into and there was a link to the part in the video so I ordered it and it came right away and it fixed it, shipping seemed a little much though but I was very satisfied overall
Read more
More
$18.44
- Compare At:
-
$21.76
- You Save:
-
$3.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP1106508
This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does
- Forms a reliable seal between components to prevent fluid or air leaks
- Maintains proper operation by keeping the sealed area contained
- Replaces gaskets that are brittle, cracked, flattened, or swollen
- Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal
What's included
Install notes
- Disconnect power and any water or gas supply before servicing
- Note the gasket's orientation; compare old and new parts before installation
- Clean and dry mating surfaces; remove old adhesive and debris
- Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly
Do-It-Yourself Stories from Customers like You
Delivery person broke fitting off for the ice maker while removeing our "good" old fridge that was already sold Donald J. • Fremont , MI • October 13, 2014
I ordered the repair parts that Lowes said they couldn't get. I got the parts very fast and only took 5 minutes to get the job done.
Read more
More
$6.42
- Compare At:
-
$7.58
- You Save:
-
$1.16
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387491
These inserts are for 1/4 inch plastic tubing. Package of 4.
More
$11.95
- Compare At:
-
$13.22
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2188756
This refrigerator unit cover mounts over the interior control/air distribution housing. It restores a clean, finished look and protects internal components by enclosing the area as designed. What it does:
- Provides a protective, finished cover for the control/diffuser housing
- Helps keep the airflow path properly enclosed inside the compartment
- Replace if the cover is cracked, warped, loose, or missing
- Common signs include rattling, visible gaps, or exposed components
What's included:
Install notes:
- Unplug the refrigerator before servicing
- Remove shelves or bins for access as needed
- Release tabs or remove screws to take off the old cover; retain hardware for reuse
- Align and secure the new cover; do not overtighten fasteners, then restore power
Do-It-Yourself Stories from Customers like You
Backing to frig broken shelves Margarita R. • Brabenton , FL • June 11, 2019
Screws and inserted shelves
Read more
More
$80.60
- Compare At:
-
$96.72
- You Save:
-
$16.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387535
This compressor overload is the thermal protector for your refrigerator's compressor. It opens the circuit when the motor overheats or draws excessive current, helping prevent damage and restoring reliable starts when the original protector fails.
- Interrupts power to protect the compressor during overheat or overcurrent conditions
- If failed, symptoms include: compressor won't start, repeated clicking or brief hum then stop, warm refrigerator/freezer, and an unusually hot compressor shell
- A weak protector may trip repeatedly and reset after cooling, causing intermittent cooling
- Works in tandem with the start relay/device to manage compressor startup current
What's included: 1 compressor overload protector Install notes:
- Disconnect power before servicing and pull the unit forward for rear access
- Remove the rear cover; note wire positions and take a photo for reference
- Pull the old overload straight off the compressor terminal; transfer leads and firmly seat the new overload in the same orientation
- Capacitors can retain a charge—handle with care; reinstall cover and restore power to test
This part fixes the following symptoms
-
Won't start
-
Fridge too warm
See more...
Do-It-Yourself Stories from Customers like You
Overload switch stopped working turning off the refrigerator compressor J Michael L. • Waxahachie , TX • August 06, 2016
Replaced overload switch and start relay with convenient repair set.Video available on website that gave step by step instructions. Followed the video steps for removal and installation.... plugged in the refrigerator compressor started up everything cool in minutes
Read more
More
$84.45
- Compare At:
-
$100.50
- You Save:
-
$16.05
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400906
This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.
- Fastens brackets, panels, ducts, or housings to the cabinet or frame
- Replaces missing, stripped, or corroded hardware
- Helps stop rattles, vibration, and loose or misaligned parts
- Maintains proper alignment for reliable operation
Includes: 1 screw
- Disconnect power; shut off gas and water before servicing
- Match this screw to the original location and hardware type used on your model
- Start threads by hand to avoid cross-threading; use the correct driver
- Snug only—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Broken ice maker door and tabs David G. • San Antonio , TX • December 22, 2018
Through your website and YouTube DIY’s I was able to find the parts for my specific refrigerator and fix it, the wife had been after me for over a year to fix it and did not. I was ready to buy a new refrigerator but decided to try and fix it myself you guys rock !
Read more
More