Kenmore Washer 110.20052994 (11020052994, 110 20052994) Parts

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

Size: 10-16 x 5/8 inch.

This driven cam bearing supports the cam in the compactor's drive assembly, reducing friction and keeping components aligned so the ram moves smoothly and the unit completes and reverses cycles reliably.

• Supports and centers the driven cam/gear for proper alignment
• Reduces friction and wear for smoother cam rotation
• Helps ensure correct switch timing so the ram reverses at end of travel
• Symptoms of wear include squealing/grinding, binding or jerky ram movement, or failure to complete a cycle

• Disconnect power at the breaker or unplug the unit before servicing
• Secure the drawer/ram to prevent unintended movement while working
• Access the drive mechanism and note the bearing's orientation on the cam before removal
• Seat the new bearing fully and hand-rotate the cam to verify smooth movement before reassembly and restoring power

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

Size: 21 inches long. Clamp included.

This oven liner replaces the damaged or corroded inner surface of the oven cavity to restore a smooth, heat-resistant interior and help reduce smoke, odors and uneven cooking caused by a compromised liner. What it does:

• Provides the oven cavity's inner surface that protects the cabinet and insulation from heat and spills
• Helps prevent hot spots and cooking inconsistencies caused by warped or missing liner sections
• Reduces smoke and burnt-food odors from residue trapped in damaged liner areas
• Restores a clean interior surface that's easier to wipe and maintain

• Disconnect power to the appliance (unplug or switch off breaker) before starting any work
• Remove oven racks and, if needed, the oven door per the manufacturer's instructions to access the liner
• Use gloves and eye protection; liners can be sharp at edges and heavy or awkward to handle
• Follow for fasteners, insulation placement and reassembly; do not operate the oven with loose or missing parts

Used for the pressure switch.

This replacement screw secures appliance panels, brackets, and components to the cabinet or chassis. The #8-15 x 1/2 in. size restores a snug, reliable hold when original hardware is missing, stripped, or corroded.

• Fastens panels, brackets, and trim to the appliance cabinet or chassis
• Helps reduce rattling, vibration, or looseness caused by missing/stripped hardware
• Restores proper alignment of parts that have shifted due to loose fasteners
• Size/spec: #8-15 thread, 1/2-inch length; use where this size is specified

• Disconnect power and shut off gas/water supplies before servicing
• Replace one screw at a time to maintain alignment of parts
• Start threads by hand to prevent cross-threading; do not overtighten
• Use a matching driver/bit type for the screw head used in your appliance

Used from harness to top.

This trim piece finishes and protects an opening or edge on your appliance's cabinet or console. Replacing a cracked or missing trim restores a clean, factory look and helps nearby components sit and operate as intended. What it does:

• Provides a clean, finished edge and covers sharp cabinet/console edges
• Helps keep adjacent parts aligned and secured around the opening
• Restores appearance when original trim is cracked, warped, discolored, or missing
• Common symptoms: loose or rattling piece, cosmetic damage, snagging edges, or poor fit of nearby parts

• 1 trim piece

• Disconnect power; if applicable, shut off gas or water. Wear cut-resistant gloves.
• Remove the existing trim by releasing clips or removing screws; note orientation and retain hardware.
• Transfer any reusable clips/inserts from the old trim to the new part.
• Align and snap/screw the new trim into place; do not overtighten.

Size: .20 Fl. Oz. (6 ml)

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

This washer hose connects the bleach dispenser to the tub, directing bleach into the wash at the proper time. Replacing a cracked or clogged hose restores proper dispensing and helps prevent leaks inside or under the machine. What it does

• Routes diluted bleach from the dispenser outlet to the washer tub
• Maintains a sealed path to help prevent drips inside the cabinet
• Supports correct timed dispensing during the fill cycle
• Common symptoms: leaks near the dispenser/cabinet, bleach left in the cup, visible cracks or kinks

• Includes: 1 bleach dispenser hose

• Disconnect power and turn off water supply before servicing
• Access the dispenser and tub connections; note the original hose routing to avoid kinks
• Remove the old hose and securely fasten the new hose to both fittings with clamps
• Run a test fill and check all connections for leaks

This cam-agitator is the replacement cam that guides the agitator's motion in compatible top-load washing machines, restoring proper agitation and helping the washer move clothes through the wash cycle effectively. What it does:

• Replaces the worn or broken agitator cam that controls the agitator's directional movement.
• Helps restore normal agitation when the agitator slips, spins freely, or fails to shift between wash and spin.
• Works with the agitator assembly to transfer drive action from the transmission to the agitator.
• Designed to fit and align with the agitator and related fasteners for reliable operation.

• Basic mechanical skill and common hand tools required; your machine's service manual for model-specific guidance.
• Disconnect power and water supply before beginning repairs to avoid shock or injury.
• Inspect related parts (agitator, dogs, bolt, and spline) and replace if worn to prevent repeat failure.

Includes suspension pads.