Kenmore Washer 110.20052994 (11020052994, 110 20052994) Parts

Replacement end cap that restores the appliance's finished edge and helps protect internal components from debris. A simple, low-cost repair to replace cracked, broken, or missing end caps and reduce trim wear. What it does:

• Covers and protects an exposed edge or end of the cabinet/trim.
• Helps prevent snagging, dirt buildup, and contact damage where the cap is missing or cracked.
• Restores the appearance and alignment of surrounding trim pieces.
• Common symptom: visible crack, loose or missing trim, rubbing or catching at the edge.

• Disconnect power and/or water supply to the appliance before beginning work when applicable.
• Inspect the mating surface and remove old adhesive or fasteners before installing the replacement cap.
• Install by aligning the cap and snapping or fastening into place; do not force—use correct fasteners if applicable.
• If surrounding trim is damaged, consider replacing affected pieces to ensure proper fit and finish.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This thrust spacer positions and supports the washer tub assembly, keeping rotating parts aligned to reduce wear and maintain smooth operation. It's a small but important part for proper drivetrain alignment in top-load washers. What it does:

• Centers and spaces the tub or agitator relative to the gearbox/shaft to prevent metal-on-metal contact
• Helps maintain correct clearance for smooth spin and agitation
• Can reduce noise and vibration caused by misalignment
• Commonly replaced when wear or damage causes rubbing, grinding, or poor spinning performance

• One thrust spacer

• Designed for use with compatible washer assemblies; follow your model's service manual for fitment and orientation
• Disconnect power and water supply before servicing the washer
• Inspect adjacent seals, bearings, and shaft components while replacing the spacer; replace any worn parts

This splash shield assembly directs and contains water inside the dishwasher tub to help protect the door area and nearby components from spray and moisture. It restores the tub's splash protection to reduce leaks and water damage risk. What it does:

• Channels spray and splashes away from the door edge and console area to help prevent moisture intrusion.
• Helps reduce leaks and water pooling around the dishwasher base or adjacent cabinetry.
• Protects wiring and electronic components from direct water exposure.
• Restores intended water containment after a damaged or missing shield.

• Disconnect power and water supply before beginning work.
• Handle gently and watch for sharp edges; wear gloves as needed.
• May require removal of the dishwasher door or access panel to reach mounting points; follow the OEM service instructions.

This aerosol spray paint restores the graphite finish on appliance surfaces for quick, low-effort cosmetic touch-ups. Use it to cover small chips, scratches and scuffs so the exterior looks uniform again. What it does:

• Matches graphite appliance finishes for spot repairs and touch-ups
• Covers visible chips, scratches and minor surface scuffs
• Restores a uniform appearance on painted metal appliance surfaces
• Helps protect exposed metal from surface corrosion after repair

• Clean and dry the surface; remove grease, dirt and loose paint before spraying
• Shake can well and test spray on a scrap piece or inconspicuous area first
• Apply in light, even coats from a recommended distance; allow coats to dry between passes
• Use in a well-ventilated area, keep away from heat/open flames, and follow all safety and disposal instructions on the can

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

For end of drain hose.

Part# is one rivet.

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This auger agitator moves ice through the refrigerator dispenser so cubes and crushed ice flow smoothly to the user. It replaces a worn or damaged auger to restore normal dispensing performance. What it does:

• Rotates inside the dispenser chute to push ice toward the dispenser outlet
• Helps prevent ice clumping and improves consistent dispensing
• Commonly replaced when ice won't dispense, dispenses slowly, or makes grinding noises
• Compatible with models that use a motor-driven auger assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the dispenser cover and ice bucket per your model's service instructions to access the auger
• Inspect for ice jams or broken plastic fragments before installing the new auger

This dispenser assembly delivers bleach and fabric softener to the washer drum at the correct time during the wash cycle, helping maintain fabric care and cleaning performance. Fits top-load washer dispenser housings that accept this assembly. What it does:

• Directs liquid bleach into the wash tub during the appropriate cycle to aid stain removal
• Releases fabric softener into the rinse cycle for softer, fresher-feeling laundry
• Replaces cracked, clogged, or non-dispensing dispenser behavior
• Helps stop leaks or overflows when the original dispenser housing is damaged

• One dispenser assembly

• Remove power to the washer before beginning any repair to avoid shock or injury
• Typical access requires opening the washer cabinet or console; refer to your service manual for model-specific steps
• Inspect dispenser housing and hoses for damage and replace if necessary to ensure a proper seal

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.