Kenmore Washer 110.28002011 (11028002011, 110 28002011) Parts

This siphon break kit prevents wastewater from siphoning back into the dishwasher, helping keep the tub and dishes clean and reducing drainback issues. Fits the dishwasher drain assembly to restore proper draining function. What it does:

• Stops backflow by breaking the siphon effect in the drain line
• Works with the dishwasher drain hose and pump to maintain one-way drainage
• Helps address symptoms like water remaining in the tub, partial drains, or water backing into the tub
• Supports proper drainage to reduce odors caused by standing water

• One siphon break kit

• Disconnect power to the appliance and turn off the water supply before starting
• Inspect the drain hose routing and secure the siphon break at the recommended height per the dishwasher's service instructions
• Use basic hand tools; hose clamps or fasteners may be required

A U-bend retainer designed to secure a U-shaped heating element or tubing in place, preventing movement and vibration for reliable operation. Fits as the replacement hold-down clip used on compatible Whirlpool HVAC and appliance assemblies. What it does:

• Secures U-shaped element or tubing to the appliance frame or mounting bracket
• Prevents rubbing or vibration that can lead to wear or noisy operation
• Helps maintain proper spacing and alignment of the element for consistent performance
• Used where a compact, U-shaped clamp is required to hold components safely

• One U-bend retainer clip as shown

• Inspect the surrounding area and replaced part for damage before installing
• Use basic hand tools; align clip over the U-bend and fasten to the designated mounting point
• Disconnect power and allow components to cool before attempting repair
• Replace with the exact OEM fasteners

This replacement brace reinforces appliance cabinet structure to restore proper alignment and reduce vibration. It helps maintain secure mounting of adjacent panels so doors and controls operate smoothly. What it does:

• Provides structural support for the appliance cabinet and connected panels
• Reduces rattling or vibration caused by loose or bent cabinet components
• Helps realign panels that are pulling away or not closing flush
• Useful when visible damage, bending, or missing support causes fitment issues

• Disconnect power and, if applicable, gas supply before starting any repair
• Remove outer cabinet panels or access panels to reach the brace mounting points
• Retain original fasteners when possible; replace damaged screws or clips as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This lower wire harness routes power and signals between the appliance's lower components, restoring electrical connections for reliable operation. It replaces a damaged or worn harness to help clear power interruptions and intermittent faults. What it does:

• Delivers power and signal connections to lower motors, switches, and sensors
• Re-establishes secure connector mating to prevent intermittent operation or loss of function
• Helps resolve symptoms such as no power to lower components, erratic operation, or related error codes
• Maintains correct wire routing and strain relief to reduce chafing or shorting

• Disconnect all power before starting — follow lockout/tagout where applicable
• Access may require removing panels or the lower access panel; keep track of fasteners
• Match connector shapes and routing to the original harness; do not force connectors
• Inspect surrounding wiring and terminals for heat damage or corrosion before reassembly

This is a replacement power cord that restores electrical connection to the appliance so it powers on safely and reliably. Use it when the original cord is damaged, frayed, or no longer making a secure connection. What it does:

• Provides the main AC power connection between the appliance and household outlet
• Replaces damaged, cut, or burned cords that cause intermittent power or no power
• Helps prevent arcing and unsafe connections when the original cord's insulation or plug is compromised
• Restores a secure line connection for?? operation and diagnostics

• One replacement power cord

• Disconnect power at the breaker or unplug the appliance before starting any work
• Inspect cord routing and strain relief; replace the strain relief if the OEM design requires it
• Secure connections to the terminal block or wiring harness per OEM orientation and torque; verify tight, corrosion-free contacts

This absorber is the factory-design replacement part that restores the appliance's intended absorption function, helping maintain normal operation and reduce related performance issues. What it does:

• Absorbs and manages moisture/condensate or trapped vapors in the appliance's system to support normal function.
• Helps prevent symptoms commonly linked to a failed absorber, such as excess moisture, unusual odors, or intermittent system cycling.
• Restores the original fit and function when the installed absorber is cracked, broken, or heavily degraded.
• Matches OEM shape and connection points for a direct replacement.

• One absorber replacement as shown

• High-level replacement: access the absorber location; no specialized calibration typically required.
• Disconnect power (and water supply if applicable) before removing panels or replacing parts.
• Handle carefully to avoid damage to surrounding components and wiring; use manufacturer-recommended fasteners.

This electronic control board is the main circuit board that runs a range of appliance functions and the user interface. Replacing a faulty board restores responsive controls, display feedback, and normal programmed cycles. What it does:

• Manages the appliance's user interface, timing, and control signals for cycles and features
• Communicates with sensors and other modules to coordinate operation
• Prevents or causes faults when failing; common symptoms include unresponsive buttons, blank or erratic display, and interrupted cycles
• Helps restore normal operation when intermittent or incorrect control behavior is traced to the main board

• Disconnect power to the appliance before starting work to prevent shock or damage
• Handle the board by the edges and avoid touching component leads or solder joints
• Transfer any required brackets or harnesses from the old board and secure all connectors firmly
• Test the appliance after installation.

This wire shield is a molded protective cover that helps keep wiring routed and protected from heat, abrasion and moving parts. It prevents chafing and reduces the risk of shorts for a safer appliance operation. What it does:

• Covers and routes wiring to protect insulation from heat and friction
• Prevents wires from contacting sharp edges or moving components
• Helps stop intermittent shorts, arcing, or wiring damage that can cause odor or failures
• Maintains proper wire position to support consistent electrical connections

• One wire shield

• Disconnect power to the appliance before beginning any work
• Secure with existing clips or fasteners; do not force or modify the part
• If wiring insulation is melted or damaged, replace wiring/harness before reassembly

This cabinet is the main outer housing that supports and protects the appliance's internal components while giving the unit its finished exterior. It restores structural integrity and proper panel alignment for safe, reliable operation. What it does:

• Provides the structural frame and mounting surface for controls, panels, and internal components
• Protects internal parts from dust, moisture, and incidental contact
• Helps maintain proper airflow and component positioning to reduce vibration and noise
• Restores correct panel alignment and closure when the original cabinet is dented, cracked, or corroded

• One cabinet

• Disconnect power (and gas, if applicable) before beginning any repair
• Installing may require removing trim, controls, and internal components; keep fasteners organized
• Use proper lifting technique and a second person for heavy or bulky cabinets to avoid damage or injury

This factory screw secures appliance panels and components, keeping them properly aligned and quiet during operation. Replace a stripped, corroded, or missing fastener to restore a snug fit and dependable performance in the original mounting location. What it does:

• Fastens brackets, panels, trim, or internal hardware to the cabinet/frame as specified by the manufacturer
• Helps maintain proper alignment and reduce rattling or vibration when a screw is worn or missing
• Direct replacement for damaged, stripped, or rusted hardware
• Used in various locations per the service diagram; match to the original position

• 1 screw

• Disconnect power (and shut off water or gas, if applicable) before servicing.
• Compare length and thread style to the original; install in the same location.
• Start threads by hand to avoid cross-threading; tighten until snug—do not overtighten.
• Reinstall any brackets or panels in the correct order.

This clamp secures a washer or dryer hose to its connection to prevent leaks and keep the hose firmly in place during operation. It replaces worn or loose clamps that allow water to escape or hoses to detach. What it does:

• Holds a washer/dryer hose to a nipple, collar or fitting to maintain a sealed connection
• Prevents water leaks caused by loose or corroded clamps
• Stops hoses from slipping off during drain or fill cycles
• Restores proper hose retention and reduces risk of water damage

• Disconnect power and turn off the water supply before starting any repair
• Inspect hose and fitting for damage; replace hose if cracked or frayed
• Use appropriate pliers or a screwdriver for the clamp style; avoid overtightening to prevent hose damage
• Verify a leak-free connection after restoring power and water

Note: Bearings are only available with the gearcase assembly.

This replacement silverware/cutlery basket holds utensils securely during dishwasher cycles to keep items organized and allow thorough cleaning. Durable molded plastic resists staining and lets water and detergent reach utensils for better wash performance. What it does

• Holds forks, knives and spoons in place so utensils don't fall through the lower rack
• Allows water and detergent to circulate around cutlery for improved cleaning
• Helps prevent scoring and nesting of utensils for more even washing
• Restores organization to the dishwasher's lower rack when the original basket is cracked or missing

• One replacement silverware/cutlery basket

• No special tools required; simply set the basket into the lower dishwasher rack
• Handle carefully to avoid sharp utensils during installation
• Follow dishwasher manufacturer's safety instructions and disconnect power if recommended before servicing