Kenmore Washer 110.72693440 (11072693440, 110 72693440) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP16123
Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.
Do-It-Yourself Stories from Customers like You
Water inlet valve was corroded and broken washer Sandra H. • Belton , MO • June 26, 2015
Replaced with new part ordered from store
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP273556
Size: 10-16 x 5/8 inch.
Do-It-Yourself Stories from Customers like You
Console screws were rusty and the other screw was broken. Denis C. • Baltimore , MD • June 20, 2018
I used a screwdriver and removed all three screws and replaced them with ones I ordered from you. The job took less than ten minutes to complete.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP367594
Adjustable front leveling leg for washers. Replaces damaged, broken, or missing feet that cause rocking and vibration. Installs at front base to level unit.
Do-It-Yourself Stories from Customers like You
Front foot was damaged Deborah L. • Mount Pleasant , WI • June 08, 2015
Replaced, it was a cinch!!!
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90016
Used from harness to top.
Do-It-Yourself Stories from Customers like You
A broken lid switch on my whirlpool stackable twin washer Joseph P. • Indialantic , FL • October 25, 2016
Fixing the problem was quite simple. First, I removed the lid assembly (thanks to the diagrams supplied by AppliancePartsPros.com!). Getting the back two screws out was very difficult because I couldn't see them from the front and I could not move the unit out of the enclosed space. After some trial and error, I located the screws which were 5/16 hex head screws and removed them with a MAGNETIC nut driver. (The magnet assures that the screw will not drop down into the mechanism). Second, I...
Read more
More
$7.44
- Compare At:
-
$8.85
- You Save:
-
$1.41
Genuine Whirlpool part
By: Whirlpool
Part Number: WP354255
A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:
- Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
- Reduces vibration and rattling during operation
- Helps doors and panels sit properly when closed
- Simple, non-electrical part — no wiring or adjustment required
What's included:
Install notes:
- Inspect the mounting hole or surface; clean debris before installing
- Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
- Disconnect power to the appliance first and follow OEM instructions
- Remove old adhesive before installing the new bumper
Do-It-Yourself Stories from Customers like You
Needed water pump and lid switch Joe N. • Palmdale , CA • November 16, 2019
I utilized your videos. The pump video implied if the leak was ignored? You would have to cut the pump off, which was what I did. The impeller also had to be cut down to the plastic collar on the motor shaft, which I used a handheld chop grinder to get through the plastic collar without damaging the shaft, because of the neglect on the leak the motor shaft had to be filed and sandpapered to accept the new pump. The harness clips on the lid switch were difficult to get to but I managed without...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP91770
Right hand side
Do-It-Yourself Stories from Customers like You
Lid was rusted bad Mike S. • San Lorenzo , CA • December 06, 2016
New parts easy fix
Read more
More
$20.27
- Compare At:
-
$21.36
- You Save:
-
$1.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP359231
Washer won't start or stops mid-cycle? A damaged lid switch shield can expose wiring to moisture, causing safety interlock failures. Simple fix.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 358277
Washer won't fill, overfills, or leaks? A faulty water inlet valve is often the cause. DIYers report 10-20 minute fixes for this common washer repair.
This part fixes the following symptoms
-
No hot or cold water
-
Will not fill with water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
Washing machine took 30 minutes to fill because the inlet valve was failing Chris G. • Dunedin , FL • June 13, 2016
I ordered the replacement inlet valve from your site, installed it in 20 minutes. the washing machine now fills to extra large capacity in 3 minutes. The machine is an old Kenmore bought new in 1985, this inlet valve is the only component to fail in the over 30 years we have had it.
Read more
More
$93.72
- Compare At:
-
$111.53
- You Save:
-
$17.81
Genuine Whirlpool part
By: Whirlpool
Part Number: WP21365
Small metal spacer washer that distributes load and maintains alignment in washer assemblies. Replace when worn, missing, or damaged to restore secure fit.
Do-It-Yourself Stories from Customers like You
Washing machine would not agitate or spin. Laurie W. • Webster , NH • March 25, 2017
We were a bit doubtful that we could find parts for this Whirlpool washing machine as it is 22 years old. We were SO pleased that not only could we find them ( with excellent customer service) but they were shipped in an appropriate time. My handy husband was then able to repair it himself :)
Read more
More
$7.40
- Compare At:
-
$8.88
- You Save:
-
$1.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62837
Knurled pin secures knobs or dials to control shafts in washers. Replace if the original is missing, worn, or damaged to stop loose or spinning knobs.
Do-It-Yourself Stories from Customers like You
Whirlpool shaking Willy P. • Victorville , CA • May 19, 2019
Weekend laundry became very noisy, our 1987 Whirlpool washer began doing a dance across the floor and the drum was banging into the inner cabinet. After doing some research and watching a few videos on Appliance parts pros website. I inspected the washer and noticed one leg the rubber coating disintegrated, decided to change all four legs, springs and lid switch. Hardest part of the job is getting the cabinet together. Ops check good.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 285205
Supports the washer transmission shaft to reduce axial wear and noise. Replace when you hear grinding sounds or experience rough operation. Confirm fit with your model number.
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP596797
Genuine Whirlpool part
By: Whirlpool
Part Number: WP94614
For mating terminal use [AP31136300].
More
$4.95
- Compare At:
-
$5.89
- You Save:
-
$0.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3351614
Size: 10-24 x 3/8 inch.
Do-It-Yourself Stories from Customers like You
Timer/control failed Gilbert G. • Lansing , IL • July 09, 2018
Replaced timer control unit, first time doing this.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP358160
This lock nut secures appliance components and resists loosening from vibration. Replacing a stripped, rusted, or missing nut restores a firm, reliable connection to reduce noise and prevent parts from shifting or backing off.
- Secures brackets, shafts, pulleys, panels, or other hardware as designed by the manufacturer
- Helps prevent fasteners from loosening due to vibration and thermal cycling
- Common fix for rattling/vibration noises and components that work loose over time
- Replaces damaged, rounded, or missing original nut to restore proper fit
What's included: 1 lock nut Install notes:
- Disconnect power and shut off gas/water supplies before servicing
- Remove the worn nut with the appropriate wrench or socket
- Start the new nut by hand to avoid cross-threading; tighten securely—do not overtighten
- Inspect the mating bolt/stud and any washers; replace if worn or damaged
Do-It-Yourself Stories from Customers like You
Dryer drum was making one heck of a racket while running Michael R. • Closter , NJ • January 08, 2015
The cylinder roller that supports the dryer drum was worn and needed to be replaced. I ordered the idler pulley shaft and associated parts as well since I wasn't sure if these were worn too.
Watching the video on the web site gave me a good idea what was involved and where to look. It wasn't my exact model and make but provided sufficient information on what to look for. The parts were exact fits which was a great relief abd the dryer is running like new again!
Read more
More
$2.09
- Compare At:
-
$4.46
- You Save:
-
$2.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP96743
Washer won't drain or leaking water? This gooseneck drain hose channels wastewater from pump to household drain. Fixes clogs and damaged tubing.
More
$55.30
- Compare At:
-
$65.25
- You Save:
-
$9.95