Kenmore Washer 110.7305813 (1107305813, 110 7305813) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: 16515
$25.76
- Compare At:
-
$30.65
- You Save:
-
$4.89
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: WP98997
$7.48
- Compare At:
-
$7.65
- You Save:
-
$0.17
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 18849
$13.61
- Compare At:
-
$16.06
- You Save:
-
$2.45
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 90984
Replace your washer's 5/16-18 hex nut if the original is stripped, missing, or corroded. Secures components during assembly and maintenance.
More
$21.46
- Compare At:
-
$25.54
- You Save:
-
$4.08
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 96894
This 15-way terminal plug provides the wire-to-wire connection used on select appliance control assemblies, restoring secure electrical connections and reliable signal/power routing. Fits into the matching terminal block for proper electrical contact. What it does:
- Re-establishes a 15-position connector between wiring harness and control/terminal block
- Helps stop intermittent operation caused by loose, damaged, or corroded plug connections
- Ensures correct routing of power and control signals when mating terminals are secure
- Used wherever a 15-way plug interface is specified on the appliance wiring harness
What's included:
Install notes:
- Disconnect power to the appliance before servicing to avoid shock or injury
- Handle terminals and wires gently to avoid bending or damaging contacts
- Confirm plug orientation and full seating into the mating terminal block during installation
- If mating terminals or wiring are damaged or corroded, replace those components as well
More
$15.60
- Compare At:
-
$18.72
- You Save:
-
$3.12
Out Of Stock
Usually ships within 4 - 14 days
Genuine Whirlpool part
By: Whirlpool
Part Number: 350733
This part fixes the following symptoms
-
Will not drain
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Would not go into agitate mode or drain Mike J. • Red Bank , NJ • April 29, 2018
I found the parts on your website and watched the video and it was fixed in no time. This parts site is always the one I go to first. I've done a number of projects and have never been disappointed.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 18642
Genuine Whirlpool part
By: Whirlpool
Part Number: 285222
Genuine Whirlpool part
By: Whirlpool
Part Number: 350367
4 port. Whirlpool and Kenmore washers.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 350384
Plunger kit includes: Plunger, rivit and nylon insert.
Do-It-Yourself Stories from Customers like You
Worn and bent wig wag solenoid plunger Rob H. • Denver , CO • November 16, 2015
Replaced it:
Loosened and lifted the wig wag solenoid
used a drill with grindstone and ground off the rivet head, swapped the new part in... BUT... the kit didnt contain the rivet clip so I had to hit the hardware store for a pushnut that fit, hopefully it will stay on.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 350532
Genuine Whirlpool part
By: Whirlpool
Part Number: 352088
Genuine Whirlpool part
By: Whirlpool
Part Number: 354244
Genuine Whirlpool part
By: Whirlpool
Part Number: 359689
The tub ring clip is a small plastic or metal fastener that secures the tub ring to the outer tub of a washing machine, holding the two components together during the wash cycle. It prevents the tub ring from shifting or separating under the vibration of spinning and agitation. Replace it if you notice the tub ring is loose, rattling during cycles, or has come free from its mounting position.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 76673
Includes 4 rubber washers, 4 metal washers, and 4 screws.
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 84867
Do-It-Yourself Stories from Customers like You
Kenmore Series 70 Washer Not Spinning Kenneth W. • Monterey Park , CA • March 16, 2014
Our Kenmore Series 70 washer no longer spun during the rinse and spin cycle. After scouring the resource on the internet, the lid switch checked out OK, so it boiled down to the wig wag solenoid unit that engages the transmission. The back panel was opened and a check with a multimeter showed one of the solenoids was an open circuit and provided no resistance reading.
Removal of the old unit required some finessing with a prying tool and hammer to force it off of the shaft. The new unit...
Read more
More