Kenmore Dryer 110.77904790 (11077904790, 110 77904790) Parts

LP gas conversion kit for dryers. Includes orifice to convert from natural gas to propane. Needed when switching fuel types or replacing missing components.

Blower housing assembly that directs airflow from the drum to the exhaust vent. Replace if cracked, damaged, or causing excessive noise in your dryer.

The dryer grounding clip is a small metal fastener that maintains a secure electrical ground connection between components inside your dryer. A proper ground is essential for safe operation and helps protect against electrical shock or appliance damage. Replace this part if it is bent, corroded, or missing, especially if you are experiencing intermittent electrical issues or completing a repair that requires re-grounding internal parts.

This is a small rubber or plastic bumper that attaches to the console area of an ice machine. It acts as a cushion to prevent vibration noise and protect surfaces from impact during operation. Replace this bumper if it is cracked, missing, or deteriorated, which can cause rattling sounds or allow the console to shift out of position.

2-position wire connector for dryers. Replaces damaged, melted, or corroded connectors in electrical wiring harnesses. Essential for restoring connections.

Size: 6 - 20 x 1 1/16 inch.

Replaces a cracked, broken, or missing dryer drum baffle. Installs inside the drum to lift and tumble clothes during the drying cycle. Easy repair.

The Door Seal is an OEM component specifically designed for Whirlpool dryers. It works to create an airtight seal between the dryer door opening and drum interior. During operation, heated air and moisture are contained within the drum thanks to this crucial seal. 

Symptoms of a worn door seal include:

• Increased drying time due to air leaks
• Clothes not drying completely before end of cycle  
• Excess humidity escaping into home
• Discoloration or residue buildup on door glass

Causes of failure are normal wear and compression over extended use, or damage from improper door closure. A worn seal degrades efficiency and performance of the dryer.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

This is the rear bulkhead panel located at the back of the dryer drum compartment. It provides structural support for the drum and helps seal the rear of the drying chamber. Replace this part if you notice excessive heat escaping from the back of the dryer, unusual noises during tumbling, or if the panel is visibly cracked or warped.

Houses and secures the lint filter in your dryer. Replace if cracked, warped, or broken to prevent lint bypass and maintain airflow. Verify fit by model.

Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.

Encloses the blower wheel and seals the housing for efficient airflow. Replace if cracked, broken, or missing to restore proper air movement.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

This signal switch controls the appliance's buzzer/alert level, letting the unit sound or change beeper volume so you can hear end-of-cycle or error alerts. It replaces a failed or intermittent buzzer control for reliable audible notifications. What it does

• Sends the control board a signal to enable or adjust the buzzer/alert tones
• Restores audible end-of-cycle and error notifications when the original switch is worn or unresponsive
• Commonly replaces switches that feel loose, don't click, or fail to change the buzzer setting
• Works as the user-accessible control for enabling/disabling or adjusting buzzer functions

• One signal switch

• Disconnect power before servicing to avoid shock or damage
• Handle wiring and connectors gently; verify and match terminals before reconnecting
• Reassemble panels and test buzzer function before full reinstallation

Covers and seals your dryer's exhaust opening to direct airflow and keep debris out. Replace if cracked, warped, or missing to maintain proper venting.