Kenmore Dryer 110.78092701 (11078092701, 110 78092701) Parts

A hinge pin assembly that secures and aligns an appliance door to its cabinet, restoring proper fit and smooth opening and closing while reducing hinge noise. What it does:

• Secures the door pivot and maintains proper door alignment for a consistent seal.
• Can correct door sag, uneven gaps, or doors that stick, scrape, or fail to close fully.
• Can reduce grinding, clicking, or binding noises caused by worn or bent hinge pins.
• Replaces worn, broken, or bent hinge components that affect door motion.

• Disconnect power to the appliance before beginning any repair.
• Support the door (use a helper or suitable block) to prevent it from dropping when removing the hinge.
• Basic hand tools are typically required; follow the manufacturer's service instructions for safe removal and reinstallation.
• Inspect adjacent hinge mounts and fasteners during installation; replace damaged mounting hardware as needed.

For mating terminal use [AP31136300].

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Dryer won't heat or flames are yellow? This butane burner orifice meters gas flow for clean, reliable ignition. Required for butane conversions.

Dryer won't start or runs intermittently? A worn door switch actuator may prevent the microswitch from engaging. This assembly restores proper operation.

If assemblies shift or rattle during dryer operation, this snap-down locator clip secures components in place. Simple snap-in installation restores alignment.

This hose kit replaces worn or damaged appliance hoses to restore proper water flow and prevent leaks. It's a direct-fit replacement for compatible Whirlpool systems and helps stop visible leaks and restore normal fill/drain operation. What it does

• Replaces cracked, split or leaking hoses to stop water loss and reduce risk of appliance damage
• Restores reliable water flow for filling and draining functions
• Helps eliminate poor draining, intermittent filling, or water pooling near the appliance
• Works with existing clamps and connections when installed correctly

• Disconnect power and shut off the water supply before starting any repair
• Inspect connection fittings and replace clamps if worn; ensure a snug, leak-free fit
• Route hoses without kinks and secure to avoid chafing or strain
• After installation, run a short cycle and check all connections for leaks

This water inlet valve assembly controls water flow into the appliance so cycles fill correctly and water-dependent functions work reliably. It replaces a worn or failing valve to restore proper water supply. What it does:

• Opens and closes to allow water into the appliance during fill cycles
• Stops water flow when the cycle or machine commands a shutoff
• Commonly replaced when the appliance won't fill, fills continuously, or leaks at the valve
• Works with the appliance's control system to meter water for proper operation

• Disconnect power and shut off the water supply before starting any repair
• Handle electrical connectors and tubing carefully; replace damaged gaskets/seals
• Verify correct hose/tube routing and secure fittings to prevent leaks

Dryer won't power on or has intermittent electrical issues? A worn terminal block socket causes loose connections. Simple DIY fix in under 30 minutes.

This finished burner funnel directs gas and air into the burner for correct flame shape and ignition. It replaces a damaged or corroded funnel to help restore even heating and reliable burner performance. What it does:

• Channels gas and air into the burner for proper mixing and flame distribution
• Helps maintain even flame across the burner for consistent cooking heat
• Can reduce ignition delays or uneven flames caused by a damaged funnel
• Works with the burner assembly; not a standalone gas valve or igniter

• Turn off gas supply and electricity to the appliance before servicing
• Replace only with the correct funnel for your burner; follow OEM diagram for orientation
• Tighten fittings by hand-first, then snug—do not overtighten; inspect for leaks after reassembly

1/4-inch hex flange nut secures panels, brackets, and hardware in dryers, ovens, and ranges. Replace if worn, stripped, or missing to restore firm connections.

Secures dryer wiring to the cabinet to prevent rubbing and interference. Replace if your wire retainer clip is broken, missing, or damaged.

Size: 6 foot long. Washers not included. This is one hose, for a set with washers order 285363. For inlet hose screen use 285452A and for inlet hose washers use 285448A

Dryer not heating or flames won't ignite? This gas valve assembly controls gas flow to restore heat. Moderate DIY repair that fixed no-heat issues.

Self-drilling screw secures panels, brackets, and trim without pre-drilling. Replace missing or stripped screws during appliance repair or reassembly.

Fix water leaks or no water flow to your dryer's steam system. This inlet valve hose assembly restores proper water delivery when the original hose fails.