Kenmore Washer Dryer Combo 110.98764792 (11098764792, 110 98764792) Parts

This is the push-to-start control knob for the appliance's control panel. It restores a secure, positive press to start a cycle when the original knob is cracked, stripped, missing, or no longer engages the switch.

• Mounts on the push-to-start switch shaft on the control panel
• Provides the user interface to press and begin a cycle
• Symptoms can include a cracked or missing knob, slipping/spinning on the shaft, or the unit not starting when pressed

• Disconnect power before servicing
• Pull the old knob straight off the switch shaft; avoid prying against the panel
• Align the flat/D-shape on the shaft with the new knob and press fully until seated
• If the knob still slips, inspect the push-to-start switch shaft for wear or damage

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This small retaining clip secures a lever mechanism inside the appliance, keeping the linkage aligned so the control operates smoothly. Replacing a bent or missing clip helps restore proper engagement and prevents the mechanism from popping loose. What it does:

• Locks the lever mechanism to its bracket or shaft
• Maintains alignment of moving linkage for consistent operation
• Replaces missing, bent, or broken retainer
• Common symptoms: loose/wobbly lever, mechanism slips out, control doesn't engage reliably

• Clip only

• Disconnect power before servicing
• Access the mechanism per your model's service information and relieve any spring/linkage tension
• Note the original orientation; use needle-nose pliers to seat the new clip fully in the groove
• Test the mechanism for smooth operation before reassembly

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area

This transition duct directs dryer exhaust from the appliance to the home vent, helping maintain proper airflow and reduce vent leaks. It keeps exhaust moving out of the cabinet for safer, more efficient drying. What it does:

• Channels dryer exhaust from the appliance outlet to the household vent
• Helps prevent lint and moisture from escaping into the cabinet or laundry area
• Can reduce long dry times and overheating caused by restricted or damaged ducting
• Commonly replaced when venting is crushed, torn, or leaking

• Disconnect power (and gas, if applicable) and move the appliance away from the wall before replacing the duct
• Inspect adjoining vent hoses and seals; replace or reseal as needed for a tight fit
• Use appropriate clamps or connectors and follow local venting codes for safe exhaust routing

This is a 10-16 x 1/2 inch appliance screw used to secure panels and components on compatible Whirlpool laundry and kitchen appliances. It restores a secure fit when a fastener is missing or stripped. What it does

• Fastens trim, panels, brackets or small components to the appliance chassis
• Replaces a lost or damaged factory screw to stop rattling or loose parts
• Matches OEM thread and length for proper engagement and holding strength
• Helps maintain alignment and safe operation of the attached part

• Use the correct screwdriver or nutdriver to avoid stripping the head
• Tighten until snug—do not overtighten to prevent damage to threads or sheet metal
• Disconnect power and follow the appliance manufacturer's safety instructions before servicing

This valve assembly controls incoming water flow to the appliance, restoring correct fill and preventing overfill or no-fill conditions when the original valve fails. It's a direct-replacement style part for affected units. What it does:

• Opens and closes to admit water during fill cycles so the appliance gets the correct amount of water
• Prevents continuous flow when closed, stopping overfills and leaks
• Helps resolve symptoms like no water fill, slow or weak filling, continuous water flow, or related fill/flood error codes
• Works with existing supply lines and mounting points when the original valve is removed

• Disconnect power and shut off the water supply before beginning service
• Drain remaining water from the appliance and have towels ready to catch drips
• Replace the old valve, reattach supply hoses and electrical connectors securely, and tighten fittings to OEM torque recommendations
• After installation, restore power and water, run a test cycle, and inspect all connections for leaks

This right-side door hinge rebuilds a worn or damaged pivot point so the appliance door opens, closes and seals properly. It restores door alignment and prevents sagging that can cause gaps and cooling loss. What it does

• Replaces the right-side door pivot to restore correct door swing and alignment
• Reduces door sag and helps maintain an even seal to improve temperature retention
• Stops rubbing, scraping or binding that can occur with a worn hinge
• Works with the existing hinge housing and fasteners when used as a direct replacement

• One right-side door hinge (single hinge)

• Install with power to the appliance off and interior removed as needed for safe access
• Support the door during replacement to prevent dropping or additional damage
• Use the OEM fasteners and torque to manufacturer recommendations; inspect surrounding parts for wear

This factory hinge supports and pivots the appliance door so it opens smoothly and closes square to the cabinet. Replacing a worn or bent hinge restores proper alignment, sealing, and overall door feel.

• Provides the pivot point and carries the door's weight for smooth operation
• Helps keep the door aligned so it closes flush and seals correctly
• Direct replacement for a bent, seized, or excessively worn hinge
• Typical symptoms: door sags or rubs, squeaks/clicks at the hinge, won't close flush or stay closed

• Disconnect power to the appliance before servicing and allow hot surfaces to cool
• Support the door during removal/installation to prevent strain on the remaining hinge
• Transfer any screws, plates, or bushings from the old hinge as shown in your model's diagram
• After installation, check door alignment and gasket contact; adjust per the service instructions if needed

This is a replacement side trim screw that secures the refrigerator side trim/finish panel, restoring a snug fit and finished appearance. Designed to match the original factory fit and finish on compatible Whirlpool units. What it does:

• Fastens the side trim/finish panel so the exterior trim sits flush and secure
• Helps stop rattling, shifting, or gaps caused by loose or missing trim screws
• Matches factory color and head style to keep a consistent exterior look
• Small hardware piece used in multiple trim/assembly locations

• One side trim screw (black)

• Use the matching screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can crack trim or strip threads
• Turn power off and remove any nearby panels if needed for safe access
• Replace all to ensure even fit

This 4-position temperature selector switch controls oven heat settings so you can select the correct cooking temperature range. It replaces a worn or faulty selector to restore reliable temperature selection on compatible ranges. What it does:

• Selects among four temperature ranges for oven heat control
• Routes power to the oven heating element based on chosen setting
• Helps resolve symptoms like inability to change temperature setting or no response when selector is turned
• Works with compatible range/stove control assemblies that use a 4-position selector

• One 4-position temperature selector switch

• Disconnect power at the breaker before starting any repair to avoid shock
• Handle terminals carefully; ensure correct wiring orientation matches original
• Reassemble panels securely

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement clamp secures flexible hoses and lines to prevent leaks and keep connections tight. It restores a secure seal so appliances move water or air without escaping at the joint. What it does:

• Secures inlet, drain or water lines to fittings and housings
• Helps stop leaks from loose or worn hose connections
• Keeps hoses from slipping off during operation or vibration
• Commonly replaced when clamps are corroded, broken, or no longer hold tension

• Inspect hose and fitting for damage before installing the new clamp
• Position clamp over the hose barb and tighten evenly until snug; avoid over-tightening
• Use appropriate tools (pliers or clamp driver) and follow appliance safety procedures
• Disconnect power and shut off water supply when working on water lines

For end of drain hose.