Kenmore Range Hood 233.5888990 (2335888990, 233 5888990) Parts

This is a direct-replacement item sold as a single replacement part to service the original Broan unit. It provides the exact component on your appliance so the unit can function as intended when the correct part is identified. What it does:

• Replaces a failed or damaged factory component to restore normal operation when matched to the correct part number
• Used when the appliance exhibits the symptom caused by a broken or missing internal component
• Prevents further damage by allowing repair with the correct OEM-designated piece
• Helps avoid whole-appliance replacement when a single serviceable part is all that's needed

• One replacement part (single unit)

• Disconnect power to the appliance before removing panels or replacing the part
• Use basic hand tools and follow OEM service instructions for safe removal and installation

This knockout plug seals unused openings on range hoods and ventilation assemblies to prevent drafts, grease, and debris from entering the cabinet or ductwork. It's a simple replacement part that restores a clean, finished fit. What it does:

• Caps unused vent or panel knockouts to stop air leaks and block debris
• Helps keep grease, dust, and small pests out of cabinets and ducts
• Restores a finished appearance after removing components or modifying panels
• Prevents drafts that can affect ventilation performance

• One knockout plug

• Disconnect power to the appliance before working on panels or venting
• Press-fit into the knockout opening; some models may require light tapping with a rubber mallet
• Ensure the plug seats fully and is flush with the panel for a proper seal
• Replace if cracked, warped, or damaged to maintain effective sealing

This tension spring restores proper tension and movement to the assembly it secures, helping switches, dampers, or small linkage return to position and operate smoothly. Use when a worn spring causes slack, poor return, or noise. What it does:

• Provides restoring force for a door, damper, or linkage to return to its resting position
• Keeps components under proper tension to prevent slipping or misalignment
• Reduces rattling and vibration caused by a loose or weakened spring
• Restores reliable mechanical action when original spring is stretched or broken

• One replacement tension spring

• Disconnect power to the appliance and remove any access panels before servicing
• Handle small springs carefully—keep track of orientation and any clips or retainers for reassembly
• Use basic hand tools; springs may be under tension—wear eye protection and follow safe handling practices

This small retainer clip secures panels and components in range hoods and ventilation units, helping keep parts aligned and preventing rattles or loose panels during operation. Simple, durable replacement for worn or broken clips. What it does:

• Holds panels, filters, or trim pieces in place to prevent shifting or vibration
• Restores secure fit when an existing clip is broken, bent, or missing
• Helps stop rattling noises caused by loose components
• Prevents filters or covers from falling out during use

• One retainer clip

• Disconnect power to the appliance before accessing internal panels or components
• Use basic hand tools (screwdriver, pliers) and gently pry or slide the old clip out to avoid damaging surrounding parts
• Replace any other damaged clips or fasteners for best results

This is a replacement screw used to fasten range hood and ventilation components, restoring secure mounting and stopping loose or rattling panels. It provides a simple, reliable fix when the original screw is missing or stripped. What it does:

• Secures trim, brackets, or internal components on the hood or ventilation assembly
• Replaces missing, damaged, or corroded screws that cause rattling or loose parts
• Restores proper fit of panels and covers for safer, quieter operation
• Helps maintain proper grounding and alignment when used in the original location

• Turn power to the appliance off before starting any service that exposes wiring or internal components
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; snug until secure to avoid damaging threads or panels
• Replace with the correct OEM screw rather than forcing it

This bushing supports and centers a range-hood or ventilation fan motor shaft to reduce wear and maintain smooth fan rotation, restoring quieter, more reliable airflow in affected units. What it does:

• Centers and supports the motor shaft to keep the fan blade aligned
• Reduces metal-on-metal contact to prevent excessive wear and rubbing noises
• Helps restore smooth, consistent fan rotation and airflow
• Commonly replaced when fan is noisy, scraping, or wobbling during operation

• Disconnect power to the appliance before starting any disassembly
• Access requires removing the blower/motor assembly—keep fasteners organized
• Inspect mating surfaces for wear; replace bushing if groove or scoring is present