Kenmore Range Hood 233.5998892 (2335998892, 233 5998892) Parts

This replacement decorative trim restores the finished appearance of your appliance by covering exposed edges and creating a clean, factory look. Ideal when original trim is dented, scratched, or missing. What it does:

• Provides a finished border around the appliance opening to improve appearance
• Covers gaps and exposed mounting edges for a clean look
• Helps keep internal components concealed from view
• Replaces damaged, bent, or missing trim that affects aesthetics

• One trim piece as shown

• Turn off and unplug the appliance or disconnect power before starting work
• Remove mounting screws or clips holding the old trim; keep hardware if reusable
• Align the replacement trim carefully and secure with the original fasteners or recommended hardware
• Handle edges carefully to avoid cuts and to prevent damage to the finish

This retaining clamp secures small components or ducting in compatible Broan ventilation assemblies to keep parts properly seated and reduce movement. It's a simple replacement for worn or missing clamps that cause loose fittings or rattling. What it does:

• Holds hoses, ducts, or internal components in place to prevent shifting during operation
• Restores a snug connection at a joint or mounting point to reduce air leaks and vibration noises
• Helps maintain proper alignment of parts so switches and seals function correctly
• Useful when an original clamp is corroded, broken, or missing

• Disconnect power to the appliance before starting any service
• Access the clamp through the hood or blower housing per the appliance service instructions
• Replace with the same orientation and seating; ensure the clamp fully engages the mating surfaces
• Check for proper seal after installation and tighten or adjust as needed

Replacement cover panel for range hood exterior housing. Restores appearance when original is cracked, dented, discolored, or missing from installation.

Replace your range hood's cracked, discolored, or missing light lens cover. This transparent lens protects the bulb and directs light downward over your cooktop.

This genuine replacement screw secures trim, panels, or components on compatible Broan ventilation products, restoring proper fit and reducing rattles or loose parts. Use when original fasteners are missing, stripped, or damaged. What it does:

• Fastens panels, grilles, or mounting brackets to maintain secure assembly
• Stops vibration-related noise caused by loose hardware
• Replaces missing or worn screws that prevent parts from seating correctly
• Helps restore original alignment and safe operation of covers and trim

• One replacement screw as shown

• Verify screw size and thread before installing; use matching hardware when replacing multiple fasteners
• Avoid over-tightening to prevent stripping or damaging mounting holes
• Disconnect power or follow appliance-specific safety procedures before accessing internal components
• Keep removed hardware organized so all originals are replaced during reassembly

This replacement screw secures trim, panels, and internal components on compatible Broan appliances to restore a solid fit and reduce rattling or loose parts. Use it to replace missing or damaged fasteners and maintain safe operation. What it does:

• Secures mounting brackets, trim pieces, or internal assemblies
• Prevents panels from vibrating, rattling, or coming loose
• Restores proper alignment and fit of affected components
• Helps stop intermittent contact or movement that can cause noise

• Disconnect power to the appliance before servicing to reduce electrical and injury risk
• Use the correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid overtightening which can strip threads or damage parts
• Keep removed hardware organized and reuse only matching OEM fasteners

This is a replacement fastener screw used to secure panels and components on compatible Broan appliances. It restores a proper fit and keeps parts held firmly in place. What it does

• Replaces missing or stripped screws that allow panels or covers to rattle or sit unevenly
• Secures mounting brackets, trim pieces, or internal components so parts stay aligned
• Helps stop vibration noise caused by loose fasteners
• Simple hardware replacement to restore safe, stable assembly

• One replacement screw, as shown

• Use the correct screw location and thread engagement; do not force misaligned parts
• Hand-start the screw to avoid cross-threading, then tighten snugly — do not overtighten
• Disconnect power or follow appliance safety procedures before removing access panels
• Replace with this exact OEM screw for best fit

This is a replacement mounting nut that secures hardware and components on compatible Broan appliances, restoring proper fastener retention and preventing looseness. What it does

• Fastens and secures panels, brackets, or components in place
• Prevents vibration-related loosening that can cause rattling or misalignment
• Replaces missing or damaged thread hardware for safe, reliable attachment
• Used wherever the corresponding bolt/stud requires a matching nut to hold parts together

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct wrench or socket size to avoid stripping the nut or mating threads
• Thread the nut on by hand first, then snug with a tool; avoid overtightening
• Inspect mating bolt/stud and threads for damage; replace if stripped or corroded