Kenmore Freezer 253.24092101 (25324092101, 253 24092101) Parts

This is a replacement retainer clip used to secure interior trim and small components on compatible refrigerators. It restores proper fit and prevents loose panels, rattles, or improperly seated trim. What it does:

• Secures trim, panels or small components in place to maintain proper alignment
• Prevents rattling, gaps, and shifting caused by broken or missing clips
• Replaces brittle or cracked clips that no longer hold parts securely
• Helps restore a clean, finished fit where the original clip has failed

• Disconnect power to the appliance before beginning any service
• Remove surrounding trim or panels carefully to access clip location; small fasteners may be present
• Press replacement clip into position until it snaps in; do not force or bend brittle plastic
• If other clips or fasteners are damaged, replace them to ensure a secure fit

This drain tube insulation cushions and thermally protects the refrigerator's defrost drain tube to help prevent condensation and ice buildup. It keeps the drain line insulated so water flows freely to the drip pan and reduces drip/ice-related issues. What it does:

• Wraps around the defrost drain tube to limit heat transfer and condensation.
• Helps prevent drain freeze-ups that can cause water pooling or slow drainage.
• Reduces the chance of water dripping inside the cabinet or onto the floor.
• Supports reliable defrost water routing to the drain pan.

• Always unplug the appliance or disconnect power before servicing.
• Access may require removing the back or inside panel; keep track of fasteners.
• Slide the insulation over the drain tube so it fully covers the exposed section; ensure it sits flat without kinks.
• If corrosion or heavy buildup is present, clean the drain tube before installing new insulation.

This cable clip secures a refrigerator's wire harness or control cables, keeping wiring routed and protected to prevent pinching or contact with moving parts. A small but important retainer for safe, tidy internal wiring. What it does:

• Holds and routes wire harnesses or cables to prevent interference with drawers, doors, or moving components
• Reduces wear and chafing on wires by keeping them away from sharp edges and heat sources
• Helps maintain reliable electrical connections by preventing strain on harnesses
• Commonly replaced when clips are broken, cracked, or missing and wires become loose or misrouted

• Turn off power to the appliance before accessing internal wiring
• Install by snapping clip onto designated frame or mounting boss and seating wire(s) into the clip
• Replace any damaged wiring or connectors discovered during installation

A single replacement mounting screw used to secure panels, brackets and trim on compatible appliances. Restores proper fit and stops rattling or loose components so panels stay aligned and stable. What it does:

• Fastens panels, brackets or trim pieces to appliance chassis
• Helps eliminate rattling, vibration noise, and loose or sagging panels
• Restores secure attachment after stripped or missing fasteners
• Works with the corresponding threaded hole or nut to hold parts in place

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Disconnect power to the appliance before servicing if panels expose electrical components
• Ensure that hardware is properly seated before tightening

This main wiring harness routes power and signals between the appliance's control module and its major components, restoring reliable electrical connections and enabling proper operation of controls and motors. What it does:

• Connects the control board to switches, sensors, motors and other electrical components
• Carries power and control signals so cycles and functions run as intended
• Helps prevent arcing and poor connections when worn or damaged wiring is replaced

• Disconnect power to the appliance before beginning any repair
• Inspect connectors and wire terminals for damage or corrosion; replace if necessary
• Route the harness along original clips and fasteners to avoid pinching or heat exposure

This replacement nameplate restores the front identification badge and cosmetic finish on the appliance, helping the unit look complete and factory-original again. It's a direct-fit exterior badge used where the original label has worn or fallen off. What it does:

• Replaces a missing, peeled, or faded exterior nameplate to restore the appliance's appearance.
• Serves as the decorative identification badge that mounts to the appliance surface.
• Helps prevent sharp edges or loose fragments from remaining after the old badge is removed.
• Useful when the original nameplate is cracked, scratched, or no longer adheres.

• One replacement nameplate

• High-level, safety-first: always unplug the appliance or disable power at the breaker before starting work near electrical components.
• Remove the old nameplate and any leftover adhesive or debris; clean and dry the mounting surface before installing the new badge.
• Align the new nameplate carefully and press firmly; handle with gloves to avoid fingerprints or cuts from edges.
• If fasteners or adhesive are required, use the OEM-specified method.