Kenmore Refrigerator 253.31420104 (25331420104, 253 31420104) Parts

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Rubber grommet cushions and seals freezer components, reducing vibration and preventing wear where wiring or rods pass through. Replace if cracked or worn.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures panels, trim, and brackets inside your refrigerator. Replace this #8-18 x 3/8 screw if the original is missing, stripped, or worn.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Routes defrost and condensation water from freezer to drain pan. Replace if cracked, clogged, disconnected, or causing water pooling in compartments.

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation

Refrigerator not cooling or freezing properly? This evaporator coil kit restores cooling performance. Moderate DIY repair with basic tools required.

Refrigerator not cooling properly? A faulty condenser may be blocking heat release. This repair requires soldering skills and sealed system experience.

The Gasket, Fresh Food Door is an OEM part for Frigidaire refrigerators. It is essential for creating a tight seal around the door of the refrigerator's fresh food compartment, preventing warm air from entering and cold air from escaping. This seal helps maintain the internal temperature, ensuring food stays fresh longer and the refrigerator operates efficiently. The gasket measures approximately 37 inches in length and 29 inches in width. 

Symptoms of a bad Fresh Food Door Gasket include:

• Condensation or frost buildup inside the refrigerator,
• The refrigerator running more frequently or for longer periods,
• Difficulty maintaining consistent temperatures in the fresh food compartment.

Causes of gasket failure can include normal wear and tear, exposure to harsh cleaning chemicals that degrade the material, or damage from frequent use.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Refrigerator Shelf is an OEM part for Frigidaire refrigerators. This shelf provides sturdy storage space within the refrigerator, helping to organize food items and maximize the use of available space. The shelf measures approximately 24 inches in width and 16.25 inches in length.

Over time, refrigerator shelves can become damaged or worn due to heavy loads, spills, or accidental impacts. These issues can compromise the shelf's stability and usability.

Symptoms of a bad refrigerator shelf include:

• Cracks or breakage in the shelf material
• Difficulty fitting the shelf securely in its slots
• The shelf sagging or failing to support items properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

Control box wiring harness assembly for refrigerators. Connects control board to components. Replace if wires are damaged, connector is cracked, or harness is worn.