Kenmore Refrigerator 253.31624100 (25331624100, 253 31624100) Parts

Center hinge bracket for refrigerators in bisque finish. Mounts between doors to support door alignment. Replace if cracked, broken, or worn.

This coil cover seal is a replacement gasket that fits around the evaporator/coil cover to help maintain an airtight seal and reduce frost and moisture buildup. It restores proper airflow control for more consistent cooling. What it does:

• Seals the coil/evaporator cover to limit warm, moist air entering the coil area
• Helps reduce frost or ice accumulation on the evaporator coil
• Supports efficient cooling and stable compartment temperatures
• Can stop short-cycling or extended run times caused by air leaks
• Prevents moisture intrusion that can lead to corrosion or odor issues

• Disconnect power to the appliance before beginning any repairs
• Remove any shelving or covers needed to access the evaporator/coil cover per your service instructions
• Clean mating surfaces and seat the seal fully around the coil cover for an even contact
• If adhesive is used, use OEM-recommended tape or adhesive and allow proper cure time before re-energizing

This outer freezer door panel restores the appearance and protective outer shell of the freezer door. It replaces a dented, rusted, or damaged outer surface so the door looks right and the cabinet is protected. What it does:

• Replaces damaged or dented outer door skin to restore normal appearance
• Protects inner insulation and door components from moisture and impact
• Helps the door close and seal properly by returning correct outer fit
• Commonly used when the door has visible dents, chips, or corrosion

• Removal of the freezer door and trim is typically required; follow the appliance service manual for disassembly
• Keep and reuse original fasteners and brackets unless replacements are specified
• Handle panel edges carefully to avoid cuts and to protect the finish

This is a complete refrigerator door assembly that replaces a damaged or worn exterior door to restore sealing, appearance, and proper closing. It ships ready to install and includes the door panel and attached components. What it does:

• Replaces a cracked, dented, or bent door to restore proper closure and insulation
• Restores cosmetic appearance and matches original fit and finish
• Ensures door seals and liner align to reduce cold-air loss and maintain temperature
• Resolves issues with the door not latching or closing smoothly

• Requires basic appliance disassembly; disconnect power and empty door before starting
• May require transfer or reuse of existing hinge hardware, gasket, or trim
• Support the door during removal/installation to avoid injury or damage

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

This corner trim kit replaces damaged or worn decorative corner pieces on the refrigerator door to restore a clean, finished appearance and help protect the door edge. Simple cosmetic repair for chipped, cracked, or loose corner trim. What it does:

• Replaces cracked, broken, or missing door corner trim to improve appearance
• Covers and protects exposed door edge from everyday wear
• Helps restore proper trim alignment and fit around the door corner
• Works with existing door shell and mounting points for a straightforward swap

• Turn off or unplug the appliance and empty the area near the door before starting
• Remove the old trim carefully to avoid scratching the cabinet or door finish
• Align new trim pieces to factory mounting points; secure using original clips or screws
• If any mounting hardware is missing or damaged, replace with OEM-specified hardware

The Refrigerator Shelf is an OEM part for Frigidaire refrigerators. This shelf provides sturdy storage space within the refrigerator, helping to organize food items and maximize the use of available space. The shelf measures approximately 24 inches in width and 16.25 inches in length.

Over time, refrigerator shelves can become damaged or worn due to heavy loads, spills, or accidental impacts. These issues can compromise the shelf's stability and usability.

Symptoms of a bad refrigerator shelf include:

• Cracks or breakage in the shelf material
• Difficulty fitting the shelf securely in its slots
• The shelf sagging or failing to support items properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.