Kenmore Refrigerator 253.31679100 (25331679100, 253 31679100) Parts

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

This door stop is the replacement limiter that keeps an appliance door from over-rotating, protecting hinges and cabinet edges. It restores consistent door travel and helps the door close smoothly and securely. What it does:

• Limits how far the door opens to prevent hinge or cabinet damage
• Helps the door close in the correct position and reduces slamming
• Fits into the door/hinge assembly to provide a stable stop point
• Common symptom: door opens too far, bangs against surrounding cabinetry, or hang/align issues

• High-level replacement — remove door/hinge trim as needed per your model's instructions
• Use basic hand tools; keep fasteners separate and note orientation for reassembly
• Disconnect power if working near electrical components (applies to ovens/microwaves)

This access cover is a replacement access panel that protects internal components and closes service openings for safe, finished appliance operation. It restores a secure, clean appearance and prevents debris from entering service areas. What it does:

• Covers and protects internal components behind service openings
• Keeps wiring and connections enclosed and out of reach
• Prevents dirt, lint, and small objects from entering service areas
• Restores a finished look and secures loose or missing panels
• Helps reduce drafts through service openings

• Disconnect power (unplug or shut off breaker) before installing
• Use basic hand tools; align tabs or screw holes before fastening
• Handle edges carefully to avoid cuts and prevent damage to surrounding trim

This tube clamp secures small tubing and lines inside the appliance to prevent movement and reduce wear. It keeps hoses and tubes routed properly so they don't rub against sharp edges or vibrate during operation. What it does:

• Holds water, drain or refrigerant tubing in place to prevent sagging and chafing
• Reduces vibration and rattling from loose lines
• Helps prevent tubing wear that can lead to leaks or pinch damage
• Keeps hoses routed neatly for reliable appliance operation

• Disconnect power and shut off water supply before beginning any repair
• Remove any access panels needed to reach the clamp location; use caution around sharp sheet metal
• Replace only the damaged clamp with the same style and secure tubing firmly but without over-tightening
• If tubing shows damage where it was rubbing, replace or repair the tubing before reinstalling the clamp

Made of Nylon with adhesive tape

This coil cover seal is a replacement gasket that fits around the evaporator/coil cover to help maintain an airtight seal and reduce frost and moisture buildup. It restores proper airflow control for more consistent cooling. What it does:

• Seals the coil/evaporator cover to limit warm, moist air entering the coil area
• Helps reduce frost or ice accumulation on the evaporator coil
• Supports efficient cooling and stable compartment temperatures
• Can stop short-cycling or extended run times caused by air leaks
• Prevents moisture intrusion that can lead to corrosion or odor issues

• Disconnect power to the appliance before beginning any repairs
• Remove any shelving or covers needed to access the evaporator/coil cover per your service instructions
• Clean mating surfaces and seat the seal fully around the coil cover for an even contact
• If adhesive is used, use OEM-recommended tape or adhesive and allow proper cure time before re-energizing

This outer freezer door panel restores the appearance and protective outer shell of the freezer door. It replaces a dented, rusted, or damaged outer surface so the door looks right and the cabinet is protected. What it does:

• Replaces damaged or dented outer door skin to restore normal appearance
• Protects inner insulation and door components from moisture and impact
• Helps the door close and seal properly by returning correct outer fit
• Commonly used when the door has visible dents, chips, or corrosion

• Removal of the freezer door and trim is typically required; follow the appliance service manual for disassembly
• Keep and reuse original fasteners and brackets unless replacements are specified
• Handle panel edges carefully to avoid cuts and to protect the finish

This is a complete refrigerator door assembly that replaces a damaged or worn exterior door to restore sealing, appearance, and proper closing. It ships ready to install and includes the door panel and attached components. What it does:

• Replaces a cracked, dented, or bent door to restore proper closure and insulation
• Restores cosmetic appearance and matches original fit and finish
• Ensures door seals and liner align to reduce cold-air loss and maintain temperature
• Resolves issues with the door not latching or closing smoothly

• Requires basic appliance disassembly; disconnect power and empty door before starting
• May require transfer or reuse of existing hinge hardware, gasket, or trim
• Support the door during removal/installation to avoid injury or damage

Specs: 4 - 24 x 0.750

Specs: 4 - 40 x 0.375