Kenmore Refrigerator 253.44333604 (25344333604, 253 44333604) Parts

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This defrost drain pan collects water from the refrigerator's automatic defrost cycle and channels it safely to the evaporator area for evaporation, helping prevent leaks and water pooling beneath the appliance. What it does:

• Collects and channels defrost water away from the freezer/refrigerator cabinet
• Prevents water from pooling under the unit, which can cause floor damage or odor
• Helps proper evaporation of defrosted water at the compressor/evaporator location
• Reduces risk of ice build-up from standing water in the cabinet

• Disconnect power to the appliance before servicing to avoid electric shock
• Remove lower access panels or kickplate to reach and replace the pan
• Inspect and clear the drain tube and heater while replacing the pan for best results
• Handle gently to avoid bending or cracking the pan

This is a replacement screw fastener used to secure panels, trim, or components on compatible Frigidaire appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or trim pieces to keep components aligned and stable
• Prevents rattling, vibration noise, and gaps caused by missing or loose fasteners
• Restores proper assembly after service or part replacement
• Helps maintain safety by keeping covers and guards firmly attached

• One screw (single fastener)

• Disconnect power or unplug the appliance before servicing
• Use the appropriate driver to avoid stripping the head; do not overtighten
• Verify the screw matches the original in length and thread before installing

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This genuine replacement screw secures appliance components and restores proper fit and stability. Use it to replace a missing or damaged fastener and stop panels, trim, or parts from shifting or rattling during normal use. What it does:

• Fastens and holds panels, brackets, or small components in place
• Restores secure attachment when an original screw is missing, damaged, or stripped
• Helps eliminate vibration, rattling, or loose-fitting parts
• Matches the OEM fit and function for reliable reassembly

• Use correct screwdriver or driver bit to avoid stripping the head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Disconnect power and remove food or contents from appliance areas as needed before servicing
• If fastener threads are damaged, replace with the exact OEM screw rather than forcing installation

This ice cream shelf rail secures the small shelf/bin on the freezer door so tubs and containers stay in place. It restores the door bin edge that holds lightweight frozen goods and keeps items from shifting during normal use. What it does:

• Replaces a cracked, broken or missing freezer door rail that allows containers to fall or tip
• Provides a stable lip for ice cream tubs, butter, and other small frozen items
• Helps restore proper fit and appearance of the freezer door storage area
• Fits into the existing door bin mounting points and holds the bin edge securely

• One ice cream shelf rail

• Unplug the appliance or shut off power before servicing to avoid electrical hazard
• Remove the door bin or ice cream shelf per your model's instructions to access the rail
• Typically snaps or screws into place; keep original fasteners if present and reuse when possible

Right hand side. For the left hand side order 241674401