Kenmore Refrigerator 253.4433360A (2534433360A, 253 4433360A) Parts

Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

This replacement screw secures designated components in your appliance to maintain a tight, rattle-free fit. Replacing missing or stripped hardware restores proper attachment and helps keep panels and trim properly aligned.

• Fastens specified parts to the cabinet or frame
• Helps maintain alignment of panels and trim pieces
• Replaces missing, stripped, or corroded screws
• Common symptoms: loose or vibrating parts, panel/trim won't stay secured, visible missing hardware

• Disconnect power to the appliance before servicing
• Hand-start threads to avoid cross-threading; use the correct driver
• Do not overtighten, especially when threading into plastic
• If replacing multiple screws, replace one at a time to maintain alignment

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

If your crushed ice comes out in large chunks or clumps, this fixed blade may be worn or broken. Works with the auger to deliver consistent crushed ice.

Specs: 1.40`` long

Forms an airtight seal between freezer door and cabinet. Replace when worn or damaged to prevent warm air leaks, frost buildup, and temperature issues.

Replacement fill tube that directs water from the inlet valve into your refrigerator's icemaker mold. Replace if cracked, damaged, or causing leaks.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Secures removable wire baskets inside your refrigerator or freezer. Replace when cracked, broken, or missing to restore stable basket alignment.

Basket hanger slide for refrigerator drawers. Installs on interior cabinet to support pull-out baskets. Replace if cracked, broken, or clips missing.

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation