Kenmore Refrigerator 253.44352408 (25344352408, 253 44352408) Parts

Secures the evaporator cover inside your refrigerator's freezer compartment. Replace this metal bracket if bent, broken, or missing to restore alignment.

White plastic hinge cover that snaps onto your refrigerator door hinge. Replace if cracked, broken, or discolored to restore a clean appearance.

Fixes refrigerator with no lights or unresponsive temperature controls. Restores power to control panel and display. Moderately difficult repair.

Replaces worn or damaged shaft support bushing in your refrigerator. Cushions rotating shafts to reduce friction and noise. Order a new bushing today.

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

Secures refrigerator hoses to fittings with spring tension to prevent leaks. Replace when clamp loses grip or shows rust. Verify fit with model number.

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Secures the grille on your refrigerator. Replace if broken, loose, or missing to ensure proper grille attachment. Confirm fit with your model number.

Foam insulation block that surrounds the evaporator coil in your refrigerator. Replace if melted, cracked, or missing to maintain proper airflow.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Water valve cap for side-by-side refrigerators. Covers and protects the water inlet valve connection. Replace if cracked, broken, or missing.

Refrigerator door stop that mounts to the cabinet to prevent the door from opening too far. Replace if broken, cracked, or missing to protect hinges.

This hanger-shelf glass is the replacement glass support used to hold and stabilize a refrigerator shelf. It restores a secure, level surface for stored items and replaces cracked or missing shelf supports. What it does:

• Supports and secures the refrigerator glass shelf to its hanger/rail
• Keeps the shelf level to prevent stored items from sliding or tipping
• Replaces broken, cracked or worn hanger supports that cause shelf instability
• Helps restore proper shelf alignment and safe storage inside the compartment

• One hanger-shelf glass replacement

• Handle glass carefully and wear cut-resistant gloves to avoid injury
• Remove shelf contents and the damaged shelf before installing the replacement
• Follow the appliance manufacturer's instructions for re-seating the glass into the hanger/rails