Kenmore Refrigerator 253.44382402 (25344382402, 253 44382402) Parts

If your crushed ice comes out in large chunks or clumps, this fixed blade may be worn or broken. Works with the auger to deliver consistent crushed ice.

Specs: 1.40`` long

Forms an airtight seal between freezer door and cabinet. Replace when worn or damaged to prevent warm air leaks, frost buildup, and temperature issues.

Replacement fill tube that directs water from the inlet valve into your refrigerator's icemaker mold. Replace if cracked, damaged, or causing leaks.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Replacement drip pan that captures defrost runoff and other liquids beneath the appliance, helping prevent puddles and odors. Fits into the base to restore proper fluid collection and reduce leaks. What it does:

• Collects and channels moisture and defrost water away from the cabinet to prevent pooling under the unit.
• Helps reduce musty odors and water damage caused by a cracked, warped, or missing pan.
• Supports bottom components and maintains proper clearance where applicable.
• Works with the appliance's existing drain path; a damaged pan can cause visible leaks or puddling.

• Disconnect power and remove any food or items from the appliance before starting.
• Access may require removing lower access panels or the toe kick; follow your model's service instructions.
• Inspect mounting tabs and surrounding seals; ensure the pan seats flat and the drain path is clear.

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Fix a fridge that has power but won't cool. This inverter board controls your compressor motor and regulates cooling. Moderate DIY repair in 1-2 hours.

Replaces the refrigerator's outer front plate when cracked, dented, rusted, or worn. Restores finished appearance and covers internal components.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.