Kenmore Refrigerator 253.4438240B (2534438240B, 253 4438240B) Parts

Ice dispenser not dispensing or crushing properly? The drive cam transfers motor rotation to advance the ice dispensing cycle. DIY repair in 30-45 minutes.

Fix intermittent refrigerator operation caused by worn or heat-damaged component sockets. This receptacle restores secure plug-in connections for reliable performance.

This damper actuator controls the air damper that directs cold air between compartments, helping maintain consistent temperatures. Replacing a worn actuator restores regulated airflow and reduces uneven cooling or temperature swings. What it does:

• Moves the air/damper door to open or close the airflow path between freezer and fresh-food sections.
• Helps balance compartment temperatures by adjusting how much cold air is shared.
• A failing actuator can cause uneven cooling, temperature fluctuations, or reduced cold air in the fresh-food compartment.
• May make clicking noises or show no damper movement when faulty.

• Disconnect power to the appliance before starting any service.
• Access typically requires removing the damper housing or control cover in the fresh-food compartment.
• Align the actuator shaft with the damper linkage, seat the gear, and reconnect the electrical connector — do not force parts.

Bypass cap replaces water filter when using external filtration or no filter needed. Allows ice maker and water dispenser to function normally.

Factory replacement screw for securing panels, brackets, and trim inside your refrigerator. Needed when original screws are missing, stripped, or corroded.

Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

This replacement screw secures designated components in your appliance to maintain a tight, rattle-free fit. Replacing missing or stripped hardware restores proper attachment and helps keep panels and trim properly aligned.

• Fastens specified parts to the cabinet or frame
• Helps maintain alignment of panels and trim pieces
• Replaces missing, stripped, or corroded screws
• Common symptoms: loose or vibrating parts, panel/trim won't stay secured, visible missing hardware

• Disconnect power to the appliance before servicing
• Hand-start threads to avoid cross-threading; use the correct driver
• Do not overtighten, especially when threading into plastic
• If replacing multiple screws, replace one at a time to maintain alignment

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

If your crushed ice comes out in large chunks or clumps, this fixed blade may be worn or broken. Works with the auger to deliver consistent crushed ice.

Specs: 1.40`` long

Forms an airtight seal between freezer door and cabinet. Replace when worn or damaged to prevent warm air leaks, frost buildup, and temperature issues.

Replacement fill tube that directs water from the inlet valve into your refrigerator's icemaker mold. Replace if cracked, damaged, or causing leaks.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.