Kenmore Refrigerator 253.4439340A (2534439340A, 253 4439340A) Parts

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

Fix a fridge that has power but won't cool. This inverter board controls your compressor motor and regulates cooling. Moderate DIY repair in 1-2 hours.

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Routes water from supply line to dispenser and icemaker. Replace if tube is cracked, leaking, kinked, or damaged to restore proper water flow.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Plastic door stop cam riser for side-by-side refrigerator freezer doors. Replaces broken, cracked, or missing stops that control door position.

This is the plastic ice storage bucket that sits beneath the ice maker in the freezer compartment to collect and hold ice cubes. It slides in and out for easy access to ice. Replace it if the bucket is cracked, warped, or if the handle is broken, which can cause ice to spill or make the bin difficult to remove.

This replacement board-switch is the electronic control that manages user inputs and basic appliance functions, restoring reliable response from the control panel. Use it to replace a faulty board causing unresponsive or erratic controls. What it does:

• Routes user inputs to the appliance's control system so buttons, knobs or touchpads register correctly.
• Activates internal relays/outputs that initiate functions; failure can cause controls to be unresponsive or commands not to execute.
• Helps stop intermittent or erratic behavior caused by a damaged or corroded control board.
• Resolves symptoms such as non-working control buttons, blank or flickering display, or inconsistent function selection.

• Always disconnect power at the breaker or unplug the appliance before starting work to avoid shock.
• Handle the board by its edges and avoid touching components; use an anti-static strap if available.
• Keep track of screws and wire connections; label or photograph harness locations before removal for correct reassembly.

Metal flat washer for refrigerator ice maker auger and other assemblies. Replaces worn, missing, or damaged washers during repairs and reassembly.

Routes water from supply to dispenser and ice maker. Replace this inlet line if cracked, kinked, or leaking to restore proper water flow in your fridge.

Single mounting screw for securing refrigerator panels, brackets, and trim pieces. Replaces worn, stripped, or missing screws to restore proper fit.

This is a push on John Guess design elbow used to connect two 5/16" plastic lines together.

Collects water from your refrigerator's defrost cycle and channels it to the evaporator. Replace if cracked, broken, or leaking underneath the unit.