Kenmore Refrigerator 253.44503607 (25344503607, 253 44503607) Parts

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.

This replacement freezer shelf restores a sturdy, level surface in the freezer compartment, helping you organize and support frozen foods safely. Replace a broken or missing shelf to regain capacity and neat, reliable storage.

• Provides a flat, stable surface for frozen items
• Seats securely on the factory shelf supports for proper fit
• Helps maintain intended spacing and airflow between levels
• Typical symptoms: cracked or broken shelf, sagging, won't sit level, or missing

• Disconnect power before working inside the appliance
• Remove food items and the old shelf; retain any reusable supports
• Align the new shelf with side rails or ledges and slide/settle into place
• Ensure the shelf is fully seated before reloading and avoid overloading

This evaporator coil cover protects the refrigerator's evaporator assembly and helps direct airflow for more consistent cooling. It replaces a damaged or missing interior cover to keep the coil shielded and the compartment operating as intended. What it does:

• Shields the evaporator coil from contact and debris to prevent accidental damage
• Helps direct cold air across the evaporator for more even cooling performance
• Reduces unwanted airflow patterns that can cause frost buildup or uneven temperatures
• Covers sharp edges on the evaporator assembly for safer access during service

• One evaporator coil cover

• Disconnect power to the appliance before beginning any repair
• Remove interior panels and shelves as needed to access the evaporator area
• Handle the evaporator and cover carefully to avoid bending fins or damaging nearby components
• Fully defrost the evaporator before installing the new cover

This shelf trim replaces the front edge molding on a refrigerator shelf to restore a finished look and help secure the shelf glass. It improves shelf appearance and helps keep items from sliding off the front edge. What it does:

• Replaces damaged, cracked, or missing front shelf trim that exposes the glass edge
• Helps hold the shelf glass in place and covers the shelf front for a neat finish
• Eliminates sharp or rough shelf edges that can catch items or cause injuries
• Restores proper fit and appearance after impacts or wear

• Disconnect power if working near electrical components; remove all items from the shelf first
• Gently lift or remove the shelf glass per your model's instructions to access the trim
• Trim typically snaps or slides onto the shelf front; align carefully and press until seated
• Handle glass and plastic parts carefully to avoid damage; use basic hand tools only if required by your model

This genuine replacement clip secures appliance components to keep panels and small parts aligned and stable, restoring fit and function. It's a small, durable fastener used where a simple snap or hold is required. What it does

• Holds trim, panels, or small components in place to prevent rattling or misalignment
• Restores secure fit where a damaged or missing clip causes loose parts
• Helps stop vibration noise caused by unsecured pieces
• Small, direct-fit part—replaces a single broken or lost clip

• Disconnect power to the appliance before starting any repair.
• Access may require removing trim or panels; keep track of fasteners.
• Press or snap the clip into place; do not force beyond fit—if it won't seat, recheck alignment.
• Wear gloves and eye protection to avoid cuts from sharp edges.

Color: Black

This drip tray catches and channels defrost and condensation water beneath the refrigerator to help prevent leaks and pool buildup under the appliance. Installs under the cabinet base where drain water collects during normal operation. What it does:

• Collects and holds defrost/condensation water from the evaporator drain.
• Directs water to the drain or evaporator to prevent leaks and floor damage.
• Reduces standing water that can cause odors or attract debris.
• Helps maintain normal drip/evaporation behavior after automatic defrost cycles.

• Disconnect power to the appliance before accessing or removing the tray.
• Remove the toe kick or access panel as required by your model to reach the tray.
• Empty any standing water and inspect for debris or damage before reinstalling.
• If the tray is cracked, warped, or shows excessive corrosion, replace to avoid leaks.