Kenmore Refrigerator 253.44503608 (25344503608, 253 44503608) Parts

Crisper drawer glide clip helps your refrigerator drawer slide smoothly. Replace if broken or drawer sticks. Confirm fit with your model number.

Collects water from your refrigerator's defrost cycle and channels it to the evaporator. Replace if cracked, broken, or leaking underneath the unit.

Refrigerator not cooling or freezing properly? A faulty evaporator coil may be causing warm temps and moisture buildup. Professional installation recommended.

Seals evaporator cover to direct airflow and prevent frost buildup. Replace if worn, cracked, or causing excess frost. Confirm fit with your model number.

Fixes refrigerator with no lights or unresponsive temperature controls. Restores power to control panel and display. Moderately difficult repair.

Left hand side. For the right hand side order 241674402

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Secures refrigerator hoses to fittings with spring tension to prevent leaks. Replace when clamp loses grip or shows rust. Verify fit with model number.

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

Secures the grille on your refrigerator. Replace if broken, loose, or missing to ensure proper grille attachment. Confirm fit with your model number.

Foam insulation block that surrounds the evaporator coil in your refrigerator. Replace if melted, cracked, or missing to maintain proper airflow.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Genuine mounting screw secures panels, brackets, and components inside your refrigerator. Replace missing, stripped, or damaged screws to stop rattling.

Water valve cap for side-by-side refrigerators. Covers and protects the water inlet valve connection. Replace if cracked, broken, or missing.

This ice cream shelf rail secures the small shelf/bin on the freezer door so tubs and containers stay in place. It restores the door bin edge that holds lightweight frozen goods and keeps items from shifting during normal use. What it does:

• Replaces a cracked, broken or missing freezer door rail that allows containers to fall or tip
• Provides a stable lip for ice cream tubs, butter, and other small frozen items
• Helps restore proper fit and appearance of the freezer door storage area
• Fits into the existing door bin mounting points and holds the bin edge securely

• One ice cream shelf rail

• Unplug the appliance or shut off power before servicing to avoid electrical hazard
• Remove the door bin or ice cream shelf per your model's instructions to access the rail
• Typically snaps or screws into place; keep original fasteners if present and reuse when possible

Replacement cover for refrigerator damper control assembly. Snaps into place over the control box. Replace if cracked, broken, or missing tabs prevent secure fit.