Kenmore Freezer 253.44833601 (25344833601, 253 44833601) Parts

This is a right-side tilt-out end cap that replaces a damaged or missing end piece on a refrigerator/freezer tilt-out bin. Restores secure mounting and proper pivoting of the bin for smooth opening and closing. What it does:

• Serves as the right end support for a tilt-out bin, providing the pivot point and cosmetic trim
• Keeps the bin aligned so it opens and closes smoothly
• Replaces cracked, broken, or worn end caps that allow the bin to sag or fall out
• Helps prevent rattling and excessive play of the tilt-out bin

• One right-side tilt-out end cap

• High-level snap-in or screw-mount replacement; remove the bin and follow OEM instructions
• Remove stored items before servicing and support the bin while replacing the cap
• Use basic hand tools; avoid forcing parts to prevent further damage

This is a replacement screw used to secure panels, trim and other appliance components to restore proper fit and reduce rattling. It matches the OEM part form and fastening function for compatible Frigidaire appliances. What it does:

• Secures panels, brackets or trim to maintain proper alignment and appearance
• Replaces missing, stripped or damaged screws that cause loose parts or vibration
• Helps prevent rattling and keeps components seated for safe operation
• Restores original fastening where a worn or corroded screw failed

• Disconnect power to the appliance before beginning any repair to avoid electrical hazard
• Use the correct screwdriver or driver bit and hand-start threads to avoid cross-threading
• Tighten until snug; avoid overtightening which can strip threads or damage panels
• If thread damage is present, replace with the correct OEM fastener (do not force)

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

This compressor grommet is a rubber mounting isolator that cushions and secures the compressor to the appliance chassis, helping reduce vibration and noise while preventing metal-to-metal contact and premature wear. What it does:

• Cushions compressor movement to reduce vibration transmitted to the cabinet
• Dampens noise and rattling caused by compressor operation
• Prevents direct metal-to-metal contact that can wear mounting points
• Helps keep the compressor positioned and secured under load

• Disconnect power to the appliance before accessing the compressor or base pan
• Replace grommets while supporting the compressor to avoid strain on lines and connections
• Inspect remaining mounting grommets; replace all worn isolators for best performance

This inner door panel for the freezer provides the interior surface and structural backing for the freezer door, restoring a clean appearance and proper support for the door liner and components. What it does:

• Replaces a cracked, dented, or warped freezer inner door surface
• Restores the interior mounting surface for bins, shelves, and the door liner
• Helps maintain a proper door seal by giving the gasket a solid backing
• Prevents exposed insulation and reduces the risk of cold air loss or moisture buildup

• Disconnect power to the appliance before starting repair
• Door removal is commonly required; support the door and follow OEM instructions
• Transfer any handles, brackets, or gaskets from the old panel to the new one if needed
• Use correct fasteners and do not overtighten; check door alignment and seal after reassembly

This genuine appliance screw secures panels and components to keep your refrigerator parts aligned and stable. A small but essential fastener, it restores proper fit and stops rattling or loose trim for reliable operation. What it does:

• Fastens panels, trim, or internal components to the appliance frame
• Restores secure fit when factory screws are missing or stripped
• Stops vibration- or temperature-related rattling caused by loose hardware
• Helps maintain proper spacing and alignment of serviceable parts

• Turn off and unplug the appliance before servicing electrical or internal areas
• Use the matching screw hole and thread engagement; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking surrounding material

This mechanical temperature control thermostat replaces the factory temperature sensing switch to restore proper refrigerator temperature regulation. It helps the appliance maintain set temperatures for safe food storage and normal cooling performance. What it does:

• Senses cabinet temperature and opens/closes the cooling circuit to regulate compressor run time.
• Commonly used when the refrigerator runs constantly or cycles too quickly.
• Works as the user-adjustable temperature control for manual-style refrigerator controls.

• Disconnect power to the appliance before starting any repair.
• Handle the sensing bulb/capillary tube gently; avoid kinks or sharp bends.
• Verify correct placement of the sensing bulb in the evaporator/probe clip per OEM location.

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.

This adhesive-backed plastic mounting clip secures wires, small hoses, or components inside appliances to reduce movement and rattling. Its low-profile design helps keep internal parts organized for quieter, safer operation. What it does:

• Holds wiring harnesses, sensor leads, or small tubing in place to prevent chafing and noise
• Reduces vibration-related contact that can cause intermittent electrical or sensor issues
• Provides a simple, non-invasive mounting point without drilling or fasteners
• Adhesive backing allows quick placement in tight or hard-to-reach areas

• Clean and dry mounting surface; remove backing and press clip firmly for full adhesion
• Allow adhesive to set per ambient temperature (avoid stress on clip during initial cure)
• Disconnect power before installing
• Replace any brittle or damaged surrounding insulation or wire loom as needed