Kenmore Refrigerator 253.52322202 (25352322202, 253 52322202) Parts

Decorative channel trim that covers the water supply tube on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Refrigerator not cooling or running too warm? A faulty thermostat prevents proper temperature regulation. This control cycles the compressor to maintain set temps.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

A replacement compressor kit designed to restore the refrigeration system's ability to cool by replacing failed compressor components. Use this kit when the compressor assembly needs service or replacement. What it does:

• Replaces failed compressor components to help restore normal cooling performance
• Stops intermittent or complete loss of cooling often caused by compressor failure
• Helps address loud humming, grinding, or continuous running tied to compressor problems
• Supports proper refrigerant flow when installed and serviced

• Disconnect power and unplug the appliance before beginning any repairs
• Compressor and sealed-system service (evacuation, vacuum, refrigerant charging) must be performed
• Use proper handling and tools for refrigerant-containing components to avoid leaks and injury

Mounting plate secures the ice maker assembly inside your refrigerator. Replace if cracked, warped, or broken to restore proper ice maker support.

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

Guides and secures the control panel indicator bulb in your refrigerator. Replace if light flickers, dims, or bulb loosens. Verify fit with your model number.

Decorative trim piece that attaches to the front edge of refrigerator shelves. Replace if cracked, broken, discolored, or missing for a clean look.

Refrigerator basket trim piece that attaches to the front edge of door or freezer baskets. Replace if cracked, broken, or missing to restore appearance.

Secures water, drain, and refrigerant tubing to prevent movement and wear. Replace if tubes are loose, vibrating, or damaged. Verify fit with model number.