Kenmore Refrigerator 253.53229301 (25353229301, 253 53229301) Parts

Support bracket that secures the condenser motor in place. Replace if bent, cracked, or broken to properly stabilize the motor assembly in your refrigerator.

Rubber grommet that cushions and secures bracket components inside your refrigerator. Replace if cracked, worn, or missing to restore proper support.

This flat glass shelf replaces a damaged or missing freezer shelf to restore usable storage space and keep frozen items organized and level. Tempered glass provides a solid, easy-to-clean surface for freezer storage. What it does:

• Replaces a cracked, chipped or missing freezer shelf so food stays supported and stable
• Restores full shelf capacity and helps prevent items from falling through gaps
• Provides a smooth, flat surface that wipes clean of spills and frost
• Fits into existing freezer shelf supports or rails (verify fit for your model)

• Handle carefully—glass is heavy and can break; wear cut-resistant gloves and eye protection
• Remove food and shelving accessories from the freezer before installing
• Slide into existing shelf supports; do not force or bend supports during installation
• If shelf has clips or stops, reuse OEM hardware; replace broken supports before installing the glass

Crisper light socket housing base for refrigerators. Installs in crisper drawer area to hold the light socket. Replace if cracked, broken, or missing.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Replaces cracked, broken, or missing front trim on refrigerator shelves. Restores the finished edge and retention lip to keep items secure.

Control box housing cover for side-by-side refrigerators. Protects internal controls and wiring. Replace if cracked, broken, or missing screws.

Decorative channel trim that covers the water supply tube on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Refrigerator not cooling or running too warm? A faulty thermostat prevents proper temperature regulation. This control cycles the compressor to maintain set temps.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.