Kenmore Refrigerator 253.54662403 (25354662403, 253 54662403) Parts

This pizza shelf is a direct-replacement oven shelf designed to support pizzas and other flat bakeware for stable, even cooking. Restores a missing or damaged shelf so trays and pans sit level during use. What it does:

• Provides a flat, stable surface for baking pizzas, sheet pans, and similar items
• Replaces a warped, bent or missing pizza shelf that prevents level cooking
• Helps keep cookware centered and supported to reduce sliding or tipping
• Durable finish resists everyday oven use and helps maintain even heat exposure

• Slide shelf onto existing oven rack supports until it sits securely; no tools typically required
• Allow oven to cool before removing or installing the shelf to avoid burns
• Clean with non-abrasive cleaners; avoid harsh scrubbing that can damage the finish
• Follow your oven manufacturer's instructions for safe use and placement

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This spring secures the meat pan rail in the refrigerator/drawer assembly so the pan tracks and stays in place during normal use. It's a simple replacement that restores proper tension and alignment for the meat pan. What it does:

• Provides tension to hold the meat pan or deli drawer on its rail
• Prevents the meat pan from slipping, sagging or rattling during use
• Restores secure engagement of the pan with the rail assembly
• Works as a direct-fit replacement for the original spring on the meat pan rail

• One meat pan rail spring

• Disconnect power to the appliance or unplug before servicing to avoid injury
• Remove the drawer/pan assembly to access the rail spring; keep track of small parts
• Use needle-nose pliers for safe removal and installation; avoid overstretching the spring

This tilt-out door bin replaces a cracked, broken or missing refrigerator door bin so you can store small food items and condiments securely. It restores a tidy door shelf and keeps items from falling when opening the door. What it does

• Provides a secure tilt-out shelf for small jars, bottles and condiments on the refrigerator door
• Replaces damaged, cracked or loose bins that no longer hold items properly
• Helps stop items from shifting or falling when the door is opened
• Matches factory fit and mounts into the existing door bin supports

• One tilt-out door bin (single piece as shown)

• Remove all items from the door and clean the mounting area before installing
• Align bin hooks with the door supports and snap into place; ensure it seats securely
• Do not force into misaligned supports; inspect supports for damage if it won't engage
• Handle plastic edges carefully; wash by hand with mild detergent and dry thoroughly

This condenser fan motor circulates air across the condenser coils to help remove heat from the refrigeration system, improving cooling efficiency and preventing overheating of components. What it does

• Spins the condenser fan blade to move air over condenser coils for proper heat rejection
• Helps maintain compressor and system temperatures during normal cooling cycles
• Can cause warm cabinet temperatures or noisy operation when worn or seized
• Stops cycling correctly if the motor fails, which may lead to extended run times

• Disconnect power to the appliance before starting any service.
• Handle sharp condenser fins and mounting hardware with care; use gloves as needed.
• Verify fan blade clearance and secure all mounting screws before restoring power.
• After installation, the motor runs quietly and the fan blade spins freely.

This replacement fan shroud screw secures the evaporator/condenser fan shroud to the appliance, helping keep the fan assembly stable for proper airflow and quiet operation. Use it to replace stripped or missing mounting hardware. What it does:

• Secures the fan shroud or mounting bracket to the appliance cabinet or fan assembly
• Helps prevent fan wobble, rubbing, and airflow disruption caused by a loose shroud
• Restores proper clearance between fan blades and shroud to reduce noise and wear

• High-level replacement—remove power to the appliance before starting work
• Use appropriate-size driver to avoid stripping the screw head
• Inspect surrounding hardware and shroud for damage; replace any damaged parts before reassembly

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.