Kenmore Refrigerator 253.54669403 (25354669403, 253 54669403) Parts

Decorative channel trim that covers the water supply tube on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Basket trim for side-by-side refrigerators. Installs around storage basket edges to provide a finished look. Replace if cracked, broken, or missing.

Refrigerator ice cream shelf rail that supports and guides the freezer shelf. Replace if cracked, bent, or broken to restore proper shelf function.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

Bearing plate for refrigerators. Provides structural support for rotating components. Replace if cracked, warped, or damaged to restore stability.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This switch kit is an electrical switch assembly used to restore reliable control of affected appliance functions. It replaces a worn or failed switch so the unit responds correctly to user inputs and power commands. What it does:

• Replaces a faulty or unresponsive control switch that can prevent operation or cause intermittent power/command issues
• Restores proper opening/closing or on/off signaling for the associated control circuit
• Helps eliminate symptoms like no response to button presses, intermittent operation, or a stuck switch
• Matches OEM fit and mounting points for a direct replacement when the original switch has failed

• One switch kit assembly

• Turn off and unplug the appliance or disconnect power at the breaker before beginning work
• Follow the appliance manufacturer's disassembly steps to access the switch; avoid damaging nearby wiring or components
• Verify electrical connections are secure and oriented as original; test function before fully reassembling

Ice sits on top and won't fall into bin? This ice maker stripper pushes cubes into the collection bin. Simple DIY repair, just remove and replace.

Replacement insulation foam block for refrigerators. Installs inside cabinet walls to maintain temperature efficiency. Order when original is missing, damaged, or compressed from wear.

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

This front ice container stores and dispenses cubed ice from the freezer door, keeping ice contained and easy to access. Replaces a cracked, warped, or missing ice bucket to restore clean ice storage and pickup. What it does:

• Holds and organizes cubed ice inside the freezer door to prevent spills
• Guides ice toward the dispenser/pickup area for reliable retrieval
• Replaces damaged or broken containers that cause ice to fall or leak
• Helps keep ice separated from other freezer items for cleaner ice

• Disconnect power to the appliance before servicing to avoid electrical hazards
• Remove the old container by sliding or lifting per your freezer's rail/clip design
• Align the replacement container with the door rails or mounting tabs and slide until it seats fully
• Clean with mild soap and water; avoid abrasive cleaners or solvents that could damage plastic

Guides and secures the control panel indicator bulb in your refrigerator. Replace if light flickers, dims, or bulb loosens. Verify fit with your model number.