Kenmore Refrigerator 253.54703406 (25354703406, 253 54703406) Parts

Rubber grommet that cushions and secures bracket components inside your refrigerator. Replace if cracked, worn, or missing to restore proper support.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Control box housing cover for side-by-side refrigerators. Protects internal controls and wiring. Replace if cracked, broken, or missing screws.

Decorative channel trim that covers the water supply tube on your refrigerator. Replace if cracked, broken, or missing to restore a clean appearance.

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Basket trim for side-by-side refrigerators. Installs around storage basket edges to provide a finished look. Replace if cracked, broken, or missing.

Actuator spring for refrigerator solenoid mechanisms. Replaces broken or worn springs that cause poor movement or engagement. Restores tension.

Replaces damaged or worn refrigerator wiring harness. Restores electrical connections between components. Order this part if your harness is frayed or broken.

Fix frozen water dispenser issues with this dispenser heater kit. Prevents ice buildup in the fill tube and restores water flow to your refrigerator.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

This rear cover replaces the damaged or missing cabinet back panel to protect internal components and restore a finished appearance. It helps keep wires and motors shielded and prevents debris from entering the appliance. What it does:

• Shields the appliance's rear components (motor, wiring, vents) from dust and physical damage
• Restores proper airflow routing and helps reduce rattling caused by loose or broken panels
• Prevents accidental contact with internal electrical components and moving parts
• Common symptom: cracked, warped, or missing rear panel; noticeable noise, drafts, or exposed wiring

• Disconnect power before starting any work
• Removal typically requires backing out screws and lifting the old panel away; keep fasteners for reuse if undamaged
• Handle edges carefully to avoid cuts; wear gloves and eye protection
• Verify panel aligns with existing screw bosses and clips; do not force into place—confirm fit before tightening

Secure solenoid clip for refrigerators. Replace if damaged, loose, or missing to ensure proper solenoid function. Confirm fit with your model number.