Kenmore Refrigerator 253.55333607 (25355333607, 253 55333607) Parts

Supports and aligns the refrigerator door at the bottom pivot point. Replace if bent, cracked, or worn to restore proper door alignment and movement.

This replacement extension support restores proper alignment and secure mounting for the appliance component it attaches to, helping stop misalignment, rubbing, or loose parts and letting the appliance operate smoothly. What it does:

• Replaces a worn, broken or missing extension support used to secure or extend a nearby panel, drawer, or assembly.
• Helps stop rattling, uneven movement, or binding caused by a damaged support piece.
• Restores proper spacing and mounting so associated parts track and close correctly.
• Works as a direct-fit replacement when the original extension is damaged or missing.

• Disconnect power (and water, if applicable) before beginning any repair.
• Handle edges carefully; use basic hand tools and keep original fasteners if reusing them.
• If mounting hardware is missing or damaged, source matching screws/clips separately.

Control rod spring for refrigerator ice maker shutoff arm. Restores proper tension to control ice production cycles. Replace if spring is missing, broken, or worn.

Replacement ice bin rail that supports and guides the freezer ice bin. Restores proper alignment when the original rail is cracked, broken, or worn.

Right side.

Refrigerator spacer maintains proper clearance and alignment between internal parts. Replace if worn, missing, or causing parts to rub or bind together.

This #8-32 x 3/8 screw secures appliance panels, brackets, and assemblies. Replace a missing or stripped fastener to keep parts tight and aligned, reduce vibration, and restore proper fit in compatible refrigerators and freezers.

• Machine-thread fastener sized #8-32, 3/8-inch length
• Secures control housings, trims, covers, and support brackets per model design
• Replaces missing, worn, or corroded screws that cause loose or rattling parts
• Helps maintain alignment and stability after service

• Unplug the appliance; shut off water if applicable
• Match thread size to the original and start by hand to avoid cross-threading
• Use the correct driver; do not overtighten, especially into plastic
• Verify component alignment and operation after fastening

• Thread size: #8-32
• Length: 3/8 inch

This is a left-side slide rail that supports and guides the crisper drawer as it opens and closes inside the refrigerator. It mounts to the interior wall of the fresh food compartment and allows the drawer to glide smoothly. Replace this rail if the crisper drawer is difficult to open, sits unevenly, falls off track, or no longer slides in and out properly.

Fix a refrigerator light that won't turn on, flickers, or has a loose bulb. This interior light socket secures the lamp and restores reliable lighting.

Replacement screw for securing refrigerator panels, brackets, and trim. Needed when original fastener is missing, stripped, or damaged during repairs.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation

Plastic grommet that supports and secures refrigerator shelves. Replaces broken, cracked, or missing grommets causing shelves to lean or sag.

Secures panels, brackets, and trim on appliances. Replace when missing, stripped, or damaged to restore a tight, rattle-free fit and proper alignment.

Basket hanger slide for refrigerator drawers. Installs on interior cabinet to support pull-out baskets. Replace if cracked, broken, or clips missing.

Plastic door stop cam riser for side-by-side refrigerator freezer doors. Replaces broken, cracked, or missing stops that control door position.

Genuine mounting screw secures panels, brackets, and covers inside your refrigerator. Replace missing, stripped, or corroded fasteners to restore secure fit.