Kenmore Refrigerator 253.61462100 (25361462100, 253 61462100) Parts

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

A replacement compressor kit designed to restore the refrigeration system's ability to cool by replacing failed compressor components. Use this kit when the compressor assembly needs service or replacement. What it does:

• Replaces failed compressor components to help restore normal cooling performance
• Stops intermittent or complete loss of cooling often caused by compressor failure
• Helps address loud humming, grinding, or continuous running tied to compressor problems
• Supports proper refrigerant flow when installed and serviced

• Disconnect power and unplug the appliance before beginning any repairs
• Compressor and sealed-system service (evacuation, vacuum, refrigerant charging) must be performed
• Use proper handling and tools for refrigerant-containing components to avoid leaks and injury

Used to hold the original electrical components to the side of the compressor.

White plastic plug insert that covers foam holes in refrigerator cabinet panels. Replaces missing, cracked, or damaged hole plugs for a clean finish.

Replacement owner's manual and care guide for your refrigerator. Essential reference document for setup, operation, and maintenance instructions.

Secures motor wiring in your refrigerator. Replace if adhesive fails or clamp breaks, causing loose wires. Confirm fit with your model number.

This coil cover seal is a replacement gasket that fits around the evaporator/coil cover to help maintain an airtight seal and reduce frost and moisture buildup. It restores proper airflow control for more consistent cooling. What it does:

• Seals the coil/evaporator cover to limit warm, moist air entering the coil area
• Helps reduce frost or ice accumulation on the evaporator coil
• Supports efficient cooling and stable compartment temperatures
• Can stop short-cycling or extended run times caused by air leaks
• Prevents moisture intrusion that can lead to corrosion or odor issues

• Disconnect power to the appliance before beginning any repairs
• Remove any shelving or covers needed to access the evaporator/coil cover per your service instructions
• Clean mating surfaces and seat the seal fully around the coil cover for an even contact
• If adhesive is used, use OEM-recommended tape or adhesive and allow proper cure time before re-energizing

This outer freezer door panel restores the exterior appearance and protective surface of the freezer door. It replaces a dented, scratched, or corroded panel so the freezer looks finished and resists everyday wear. What it does:

• Replaces the damaged outer surface of the freezer door to improve appearance.
• Protects internal door components and insulation from impacts and moisture.
• Helps seal and align the door edge when installed correctly.
• Commonly replaced for visible dents, scratches, peeling, or rust on the door exterior.

• Intended for replacement by someone comfortable with appliance trim removal; retain all screws and clips during disassembly.
• Disconnect power (and empty the door area) before starting to avoid injury and damage.
• Handle edges carefully to avoid cuts and protect finished surfaces from scratches.
• Fit and final alignment may require minor adjustment of door trim or hinges; follow OEM diagram for correct fastener locations.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.