Kenmore Refrigerator 253.61662100 (25361662100, 253 61662100) Parts

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

Used to hold the original electrical components to the side of the compressor.

White plastic plug insert that covers foam holes in refrigerator cabinet panels. Replaces missing, cracked, or damaged hole plugs for a clean finish.

Replacement owner's manual and care guide for your refrigerator. Essential reference document for setup, operation, and maintenance instructions.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Secures motor wiring in your refrigerator. Replace if adhesive fails or clamp breaks, causing loose wires. Confirm fit with your model number.

This coil cover seal is a replacement gasket that fits around the evaporator/coil cover to help maintain an airtight seal and reduce frost and moisture buildup. It restores proper airflow control for more consistent cooling. What it does:

• Seals the coil/evaporator cover to limit warm, moist air entering the coil area
• Helps reduce frost or ice accumulation on the evaporator coil
• Supports efficient cooling and stable compartment temperatures
• Can stop short-cycling or extended run times caused by air leaks
• Prevents moisture intrusion that can lead to corrosion or odor issues

• Disconnect power to the appliance before beginning any repairs
• Remove any shelving or covers needed to access the evaporator/coil cover per your service instructions
• Clean mating surfaces and seat the seal fully around the coil cover for an even contact
• If adhesive is used, use OEM-recommended tape or adhesive and allow proper cure time before re-energizing

This outer freezer door panel restores the appearance and protective outer shell of the freezer door. It replaces a dented, rusted, or damaged outer surface so the door looks right and the cabinet is protected. What it does:

• Replaces damaged or dented outer door skin to restore normal appearance
• Protects inner insulation and door components from moisture and impact
• Helps the door close and seal properly by returning correct outer fit
• Commonly used when the door has visible dents, chips, or corrosion

• Removal of the freezer door and trim is typically required; follow the appliance service manual for disassembly
• Keep and reuse original fasteners and brackets unless replacements are specified
• Handle panel edges carefully to avoid cuts and to protect the finish

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.