Kenmore Refrigerator 253.61894803 (25361894803, 253 61894803) Parts

The refrigerator ice maker hole plug is a rubber or plastic cap that seals the pre-drilled opening in the refrigerator cabinet wall that is used for ice maker water line connections. It keeps cold air from escaping through the unused hole in refrigerators that do not have an ice maker installed. Replace or install this plug if cold air is leaking through an open hole in the back wall of the refrigerator, causing temperature fluctuations or frost buildup.

Support bracket that secures the condenser motor in place. Replace if bent, cracked, or broken to properly stabilize the motor assembly in your refrigerator.

Rubber grommet that cushions and secures bracket components inside your refrigerator. Replace if cracked, worn, or missing to restore proper support.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Bisque plug insert for refrigerator door hinge bearing hole. Replaces missing, cracked, or damaged plugs. Covers hinge pin opening for clean finish.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Foam insulation block that fills gaps inside the refrigerator cabinet to reduce heat transfer. Replaces damaged, compressed, or missing insulation.

Plastic plug insert for refrigerator panels and structural openings. Replace if cracked, broken, or missing to maintain proper cabinet appearance.

Refrigerator not cooling or running constantly? A faulty condenser coil prevents heat release. This repair requires moderate skill and 1-2 hours to complete.

This tube connector is a small water-line fitting that joins refrigerator water and ice-maker tubing, restoring a secure path for water flow. It helps stop leaks and regain consistent water delivery to the dispenser or icemaker. What it does:

• Joins two sections of refrigerator water tubing to maintain a watertight connection
• Stops leaks at a damaged or worn tube joint
• Restores water flow to the ice maker or dispenser when a broken connector is the cause
• Compatible with rigid and soft tubing in typical refrigerator plumbing layouts

• One tube connector

• Shut off the refrigerator water supply before servicing
• Inspect tubing ends and replace damaged tubing or seals as needed
• Use proper fittings and tighten to manufacturer torque; avoid over-tightening

Replace your refrigerator's handle trim piece. This decorative cover installs over the door handle. Order a new trim if yours is cracked or missing.

Replaces a broken or worn refrigerator door stop that limits door travel. Prevents over-rotation damage to hinges and cabinet. Restores smooth closing.

Secures motor wiring in your refrigerator. Replace if adhesive fails or clamp breaks, causing loose wires. Confirm fit with your model number.

This outer freezer door panel replaces a cracked, dented or cosmetically damaged front to restore the freezer's appearance and fit. Designed to match the original door's shape and mounting points for a clean finish. What it does:

• Replaces a damaged or scratched freezer door front to improve appearance
• Provides proper surface for existing handle and trim to reattach
• Restores alignment and sealing where outer panel wear causes misfit
• Helps protect the inner door liner and components from external damage

• One outer freezer door panel

• Basic disassembly of freezer door trim and handle required; keep all fasteners for reassembly
• Transfer any hardware, insulation, or inner panel pieces only if instructed by the OEM
• Use proper support for the door during work to avoid bending or injury
• Disconnect power to the appliance before major disassembly and follow safety guidance

This outer refrigerator door panel replaces a damaged or dented exterior door shell to restore appearance and protect internal components. It provides a clean, finished look and a solid mounting surface for door hardware. What it does

• Replaces the exterior door shell to cover and protect the inner liner and insulation
• Restores a smooth, undented finish so the refrigerator looks like new
• Provides the mounting surface for trim, handles, seals, and other door hardware
• Helps maintain proper door alignment and fit for effective sealing

• Designed for swap-out of the existing outer panel; remove door from appliance per manufacturer instructions before beginning.
• Handle, trim, insulation, and screws may need to be transferred from the old panel.
• Use proper tools and an assistant for heavy or awkward doors to avoid damage or injury.
• Disconnect power and follow all safety precautions.