Kenmore Refrigerator 253.68884014 (25368884014, 253 68884014) Parts

This foam insulation block helps fill gaps and reduce heat transfer inside the refrigerator cabinet to maintain proper cooling and reduce frost/condensation. It restores the designed insulation barrier where the original piece is damaged or missing. What it does:

• Replaces a damaged or missing foam block that seals internal gaps in the cabinet or behind panels
• Helps prevent warm air infiltration that can cause poor cooling or excess frost
• Reduces condensation and moisture buildup around the evaporator area or panel seams
• Supports consistent temperature performance by restoring insulation continuity

• One foam insulation block

• Disconnect power to the appliance before beginning any repair
• Access location may require removing interior panels or shelves; handle panels and clips carefully
• Install in the exact position and orientation of the original part; use any existing adhesive or fasteners as required
• If adhesive is needed, use only appliance-safe adhesives compatible with foam and follow manufacturer guidance

This door stop is the replacement limiter that keeps an appliance door from over-rotating, protecting hinges and cabinet edges. It restores consistent door travel and helps the door close smoothly and securely. What it does:

• Limits how far the door opens to prevent hinge or cabinet damage
• Helps the door close in the correct position and reduces slamming
• Fits into the door/hinge assembly to provide a stable stop point
• Common symptom: door opens too far, bangs against surrounding cabinetry, or hang/align issues

• High-level replacement — remove door/hinge trim as needed per your model's instructions
• Use basic hand tools; keep fasteners separate and note orientation for reassembly
• Disconnect power if working near electrical components (applies to ovens/microwaves)

A small replacement mounting clip that secures interior trim and panels to restore proper fit and reduce rattling. Use when a broken or missing clip leaves gaps or lets panels or trim sit loose on the appliance. What it does:

• Secures trim, access panels or small plastic covers to the appliance frame
• Restores proper alignment and helps eliminate panel vibration or rattling
• Replaces cracked, worn or missing clips that allow gaps or loose parts
• Works as a simple fastener where the original clip has failed

• Always disconnect power to the appliance before beginning any repair
• Clip typically installs with a push-fit or snap-in motion; a flat tool may help remove the old clip
• Handle surrounding trim gently to avoid cracking brittle plastic
• Verify correct clip orientation before snapping into place

Made of Nylon with adhesive tape

This service data sheet is a factory service insert that provides wiring diagrams, component locations and basic diagnostic notes to help troubleshoot and repair the appliance. It's a reference document meant for service use. What it does:

• Shows wiring diagrams and connector pinouts to help identify electrical routing and connections
• Lists component locations and part callouts so technicians can find and verify parts
• Includes basic diagnostic notes or service instructions commonly used during repairs
• Helps confirm original factory specifications and correct service procedures

• One factory service data sheet (single folded/printed insert)

• This is an informational/service document, not a replaceable mechanical or electrical component
• Keep sheet protected from moisture and grease; store with appliance documentation
• Use only for reference; follow all safety procedures and disconnect power before servicing appliance

This repair parts list is the printable parts diagram and reference sheet used to identify service parts and part locations. It helps you find the correct replacement parts and part numbers when planning a repair. What it does:

• Provides an exploded-view diagram showing part locations and reference numbers
• Lists part names and reference numbers to match against ordering tools
• Helps troubleshoot by clarifying component placement and assembly relationships
• Speeds parts lookup and reduces ordering errors when paired with model info

• No installation required; this is a reference document only
• Keep with appliance documentation or service records for future repairs
• If printing, use legible settings to ensure diagram details remain clear
• Verify diagram matches your appliance model before ordering parts

This is a sliding shelf frame that is used on the interior of many models of refrigerators. The shelf frame supports the shelves used to hold food and beverages inside the appliance. Regular use can cause wear and tear to the sliding shelf frame.No specific tools are needed to replace this part. Open the fridge to access the damaged shelf. Pull the entire shelf out of the appliance and gently remove the glass shelf from the plastic frame. Insert the glass into the new frame and place it in the refrigerator. Make sure it is secure before use.This sliding shelf frame is designed for use with refrigerators manufactured by Kelvinator, Frigidaire, Crosley, Kenmore, and Westinghouse. It is sold as an individual product. This is an authentic OEM replacement part that is directly sourced from the manufacturer.