Kenmore Refrigerator 253.69959704 (25369959704, 253 69959704) Parts

Replacement mounting screw for refrigerator panels, trim, and brackets. Needed when original screws are missing, stripped, or damaged during repairs.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Routes defrost and condensation water from freezer to drain pan. Replace if cracked, clogged, disconnected, or causing water pooling in compartments.

Secures the compressor to the mounting bracket in your refrigerator. Replace if washer is missing, cracked, or worn to restore proper support.

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation

Freezer not freezing or fridge too warm? The evaporator coil absorbs heat to cool your refrigerator. Professional installation recommended for this repair.

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Internal wiring harness that routes power between your refrigerator's electrical components. Replace if damaged, chewed by rodents, or frayed.

Restores tight seals to stop leaks, drafts, and temperature loss. Replace when you notice gaps, noise, or moisture issues. Verify fit with your model.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Replaces broken or missing can dispenser for refrigerator door or shelf. Holds and organizes canned beverages. Snaps or hooks into place for neat storage.

A replacement starter kit used to restore reliable starting operation in compatible Frigidaire appliances. Replaces the original starter components so the appliance can more consistently begin motor/compressor cycles. What it does

• Provides the starter components needed to engage the motor or compressor during power-up.
• Helps resolve symptoms like failure to start, intermittent starts, or humming without run.
• Restores normal starting sequence when starter components are worn or failed.
• Works as a direct-replacement kit for the OEM starter assembly where specified.

• For experienced DIYers only; disconnect power before servicing.
• Follow OEM service instructions for correct routing, mounting, and electrical connections.
• Inspect related components (capacitor, relay, motor) for damage before installation.

Black button plug that covers upper hinge mounting holes on your refrigerator. Replace if original plug is missing, cracked, or broken for a clean finish.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard