Kenmore Air Conditioner 253.70151011 (25370151011, 253 70151011) Parts

This electronic control board is the appliance's main PCB that manages functions and the user interface. Replacing a failed board can restore normal operation when the unit is unresponsive, erratic, or displaying control-related errors.

• Directs operation of key components based on user settings and sensor feedback
• Powers and communicates with the display/interface and control pads
• Coordinates timing through relays and interfaces with safety/protection circuits
• Common symptoms: no response to buttons, dead/blank display, unexpected cycling or beeping, control error codes, or visible damage on the old board

• Disconnect power before servicing and verify no voltage is present
• Use ESD precautions; handle the PCB by the edges and avoid flexing it
• Photograph/label connectors; transfer each to the same location on the new board, matching any jumpers or DIP-switch settings if present
• After installation, restore power and run the model's test/diagnostic or a cycle to confirm proper operation

This handheld remote control sends wireless commands to your appliance so you can change settings from a distance. It replaces a lost or non-working remote to restore convenient, button-based control of functions and modes. What it does:

• Sends infrared/wireless signals to the appliance receiver to change settings
• Lets you adjust common functions such as power, mode and temperature/fan settings
• Restores remote operation when the original remote is lost, damaged or unresponsive
• Resolve issues where the appliance doesn't respond to remote commands

• Install fresh batteries before first use and after long storage; use correct battery type
• Point remote at the appliance receiver and test from several feet away; remove obstructions
• If the appliance doesn't respond, check receiver/IR sensor and power to the appliance
• Handle electronic parts carefully; disconnect power to the appliance before servicing internal components

This replacement power cord restores AC power to compatible refrigerators by replacing a damaged or worn supply lead. It provides a direct, safe power connection so the appliance can run reliably. What it does:

• Replaces a frayed, cut, or otherwise damaged power supply cord
• Restores consistent power when the appliance will not turn on or has intermittent power
• Maintains the appliance's grounding connection for safe operation
• Prevents electrical arcing from exposed wiring or compromised insulation

• One replacement power cord

• Disconnect the appliance from the power source before inspecting or replacing the cord
• Install with the proper strain relief and secure fasteners to prevent pinching or pull-out

This oven temperature sensor detects the internal temperature and sends readings to the range control so the oven can maintain accurate cooking temperatures. Replaces a failed or intermittent sensor to restore reliable temperature control. What it does:

• Senses oven cavity temperature and provides temperature data to the control board
• Helps the control maintain set bake/roast temperatures
• Common symptom: oven temperature is incorrect or fluctuates during cooking
• Common symptom: cook cycles take too long or oven does not reach set temperature
• Common symptom: oven displays a temperature sensor or sensor fault code

• One oven temperature sensor (1 each)

• Disconnect electrical power to the appliance before removing or installing the sensor
• Handle the sensor carefully to avoid damaging the probe or wiring and ensure proper connector seating
• Inspect wiring and connector for damage; replace if frayed or corroded

This replacement blade fan moves cold air across the evaporator to help maintain even temperatures inside the compartment. It restores proper airflow for more consistent cooling and helps reduce frost buildup when working with a good motor. What it does:

• Circulates air across the evaporator to distribute cold air through the compartment
• Restores airflow when a cracked, warped, or missing blade reduces cooling efficiency
• Helps reduce uneven temperatures and localized warm spots caused by poor airflow
• Can reduce abnormal noises caused by damaged or unbalanced blades

• One replacement blade fan

• Disconnect power to the appliance before starting any repair
• Remove the evaporator cover/panel to access the fan assembly per your model's service instructions
• Handle the replacement blade carefully to avoid bending the blades or contaminating the evaporator
• If the fan motor or mounting hardware is damaged, replace those parts as well for reliable operation

This blower wheel is the rotating fan component that moves air through the appliance to maintain proper airflow and temperature control. Replacing a worn or damaged wheel restores efficient air movement for normal operation. What it does:

• Spins with the blower motor to circulate air across the evaporator or heat exchanger
• Restores proper airflow when the original wheel is cracked, broken, or missing fins
• Helps reduce unusual noise caused by a warped or imbalanced wheel
• Can improve cooling/heating performance tied to insufficient airflow

• One blower wheel

• Disconnect power to the appliance before starting any repair
• Remove access panels carefully; watch for sharp edges
• Inspect the blower motor shaft and set screw/retaining clip; replace any worn fasteners
• Ensure the wheel is correctly seated and secured to avoid imbalance and noise

This screw kit is a replacement hardware pack used to restore secure fastening of appliance panels and components. It provides the standard mounting screws needed when original fasteners are missing, damaged, or worn. What it does:

• Replaces missing or stripped screws that hold panels, trim, or small assemblies in place
• Restores secure fit to reduce rattling, vibration, or loose parts
• Helps correct minor alignment issues caused by lost fasteners
• Useful when preparing for panel removal/reinstallation during service

• Disconnect power to the appliance before servicing.
• Use the correct screwdriver or driver bit to avoid stripping screw heads.
• Tighten screws until snug; avoid overtightening to prevent damage.
• Follow OEM service instructions.