Kenmore Refrigerator 253.70754400 (25370754400, 253 70754400) Parts

This foam insulation block helps fill gaps and reduce heat transfer inside the refrigerator cabinet to maintain proper cooling and reduce frost/condensation. It restores the designed insulation barrier where the original piece is damaged or missing. What it does:

• Replaces a damaged or missing foam block that seals internal gaps in the cabinet or behind panels
• Helps prevent warm air infiltration that can cause poor cooling or excess frost
• Reduces condensation and moisture buildup around the evaporator area or panel seams
• Supports consistent temperature performance by restoring insulation continuity

• One foam insulation block

• Disconnect power to the appliance before beginning any repair
• Access location may require removing interior panels or shelves; handle panels and clips carefully
• Install in the exact position and orientation of the original part; use any existing adhesive or fasteners as required
• If adhesive is needed, use only appliance-safe adhesives compatible with foam and follow manufacturer guidance

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

This trough drain is the molded drain channel that guides defrost and condensation water safely to the refrigerator drain system, helping prevent puddling and water damage under the cabinet. What it does

• Collects and channels meltwater and condensation from the evaporator/defrost area into the drain outlet
• Helps prevent water pooling inside the freezer or under the fridge base
• Reduces risk of ice buildup and recurring water leaks in the cabinet
• Restores proper drainage when a cracked or clogged trough causes overflow

• One trough drain

• Disconnect power to the appliance before starting any repair
• Remove food, shelves, and access panels as needed to reach the drain trough
• Inspect surrounding seals and the drain tube for clogs or damage when replacing the trough
• Follow steps for proper removal and reinstallation; use OEM fasteners and gaskets if required

This door stop is the replacement limiter that keeps an appliance door from over-rotating, protecting hinges and cabinet edges. It restores consistent door travel and helps the door close smoothly and securely. What it does:

• Limits how far the door opens to prevent hinge or cabinet damage
• Helps the door close in the correct position and reduces slamming
• Fits into the door/hinge assembly to provide a stable stop point
• Common symptom: door opens too far, bangs against surrounding cabinetry, or hang/align issues

• High-level replacement — remove door/hinge trim as needed per your model's instructions
• Use basic hand tools; keep fasteners separate and note orientation for reassembly
• Disconnect power if working near electrical components (applies to ovens/microwaves)

This access cover is a replacement access panel that protects internal components and closes service openings for safe, finished appliance operation. It restores a secure, clean appearance and prevents debris from entering service areas. What it does:

• Covers and protects internal components behind service openings
• Keeps wiring and connections enclosed and out of reach
• Prevents dirt, lint, and small objects from entering service areas
• Restores a finished look and secures loose or missing panels
• Helps reduce drafts through service openings

• Disconnect power (unplug or shut off breaker) before installing
• Use basic hand tools; align tabs or screw holes before fastening
• Handle edges carefully to avoid cuts and prevent damage to surrounding trim