Kenmore Refrigerator 253.70894408 (25370894408, 253 70894408) Parts

Bisque plug insert for refrigerator door hinge bearing hole. Replaces missing, cracked, or damaged plugs. Covers hinge pin opening for clean finish.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Foam insulation block that fills gaps inside the refrigerator cabinet to reduce heat transfer. Replaces damaged, compressed, or missing insulation.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Replace your refrigerator's handle trim piece. This decorative cover installs over the door handle. Order a new trim if yours is cracked or missing.

Wiring harness for top-mount refrigerators. Connects electrical components throughout the unit. Replace if wires are frayed, damaged, or connectors broken.

Mounting plate secures the ice maker assembly inside your refrigerator. Replace if cracked, warped, or broken to restore proper ice maker support.

This is a Plazcrew #8-10 screw used to fasten appliance panels, trim and components. It replaces lost or damaged screws to restore secure fit and reduce rattling or loose parts. What it does:

• Secures panels, brackets, trim pieces and small appliance components
• Restores proper alignment and prevents vibration-related noise
• Replaces missing or stripped fasteners that cause loose or wobbly parts
• Matches OEM fit for repair and maintenance where this screw is specified

• Disconnect power and follow appliance safety procedures before working
• Use the correct sized screwdriver or driver bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or component damage
• Keep small parts away from children and work over a tray to avoid loss

Replaces a broken or worn refrigerator door stop that limits door travel. Prevents over-rotation damage to hinges and cabinet. Restores smooth closing.

Secures motor wiring in your refrigerator. Replace if adhesive fails or clamp breaks, causing loose wires. Confirm fit with your model number.

This is a manufacturer service data sheet that gives technicians the official service and diagnostic information needed to troubleshoot and repair the appliance. It helps locate parts and follow service procedures. What it does:

• Supplies official service and diagnostic information to guide repairs and troubleshooting
• Identifies component locations and wiring relationships to aid diagnosis
• Clarifies service procedures and specifications technicians use during repairs

• This is a reference document, not an electrical or mechanical replacement part.
• Use only as a technician reference; follow all safety guidelines when servicing the appliance.
• Keep the sheet dry and store with other service literature for future use.

Replacement owner's manual for your refrigerator. Provides operating instructions, maintenance guidelines, and troubleshooting tips for your appliance.

This outer freezer door panel replaces a cracked, dented or cosmetically damaged front to restore the freezer's appearance and fit. Designed to match the original door's shape and mounting points for a clean finish. What it does:

• Replaces a damaged or scratched freezer door front to improve appearance
• Provides proper surface for existing handle and trim to reattach
• Restores alignment and sealing where outer panel wear causes misfit
• Helps protect the inner door liner and components from external damage

• One outer freezer door panel

• Basic disassembly of freezer door trim and handle required; keep all fasteners for reassembly
• Transfer any hardware, insulation, or inner panel pieces only if instructed by the OEM
• Use proper support for the door during work to avoid bending or injury
• Disconnect power to the appliance before major disassembly and follow safety guidance