Kenmore Refrigerator 253.7419440M (2537419440M, 253 7419440M) Parts

Foam insulation block that fills gaps inside the refrigerator cabinet to reduce heat transfer. Replaces damaged, compressed, or missing insulation.

This tube connector is a small water-line fitting that joins refrigerator water and ice-maker tubing, restoring a secure path for water flow. It helps stop leaks and regain consistent water delivery to the dispenser or icemaker. What it does:

• Joins two sections of refrigerator water tubing to maintain a watertight connection
• Stops leaks at a damaged or worn tube joint
• Restores water flow to the ice maker or dispenser when a broken connector is the cause
• Compatible with rigid and soft tubing in typical refrigerator plumbing layouts

• One tube connector

• Shut off the refrigerator water supply before servicing
• Inspect tubing ends and replace damaged tubing or seals as needed
• Use proper fittings and tighten to manufacturer torque; avoid over-tightening

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Replace your refrigerator's handle trim piece. This decorative cover installs over the door handle. Order a new trim if yours is cracked or missing.

Refrigerator not cooling properly or running warm? This heat exchanger kit helps restore proper cooling in the sealed system. Advanced repair component.

Replaces a broken or worn refrigerator door stop that limits door travel. Prevents over-rotation damage to hinges and cabinet. Restores smooth closing.

Owner's manual and care guide for your refrigerator. Replacement documentation for lost or damaged manuals. Includes operating instructions and more.

Support plate for freezer interior mounting. Replaces cracked, broken, or missing support plates that compromise shelf or component stability.

Official service data sheet with wiring diagrams and diagnostic references. Replace missing or damaged technical documentation for your appliance.

This freezer door restores a secure, insulated closure to the freezer compartment and improves the appliance's appearance. It replaces a damaged, dented, or warped door to help maintain proper cooling and energy efficiency. What it does:

• Replaces the freezer compartment's outer door panel to restore a tight seal and proper closure.
• Helps stop cold air loss that can cause excessive frost, longer run times, or warm/freezer temperature issues.
• Restores the exterior finish and protects internal door components from damage.
• Useful when the original door is dented, cracked, bent, or has cosmetic damage.

• One freezer door outer panel

• Disconnect power to the appliance before starting any repair.
• Support the door while removing hinge fasteners; doors are heavy and can shift unexpectedly.
• Hinge screws, trim, handle, gasket, or insulation may need to be transferred from the old door.
• After installation, check door alignment and seal; adjust hinges as needed for a proper fit.

A small spring-style hose clamp that secures appliance hoses and tubing to fittings to help prevent leaks and hose separation. Simple, durable clamp replacement for worn or damaged hose connections. What it does

• Holds rubber or plastic hoses firmly on barbed fittings to maintain a sealed connection.
• Helps stop water or air leaks caused by loose or deteriorated hose attachments.
• Reduces movement and rattling at hose connection points during operation.
• Commonly replaced when clamps are corroded, stretched, or no longer spring-tight.

• Disconnect power and water supply before servicing the appliance.
• Use pliers to open the spring clamp, slide into position, then release so it seats evenly around the hose.
• Inspect the hose and fitting for damage; replace hose if cracked or brittle.
• Wear eye protection and gloves; ensure clamp sits behind the hose barb for a secure seal.