Kenmore Refrigerator 253.7419940S (2537419940S, 253 7419940S) Parts

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Fix no ice production or leaking ice maker with this mold assembly. Common when water doesn't fill properly or ice freezes together. Moderate DIY repair.

Refrigerator not cooling properly or running warm? This heat exchanger kit helps restore proper cooling in the sealed system. Advanced repair component.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Replacement lever arm for refrigerator ice dispensers. Installs in the dispenser housing to activate ice release. Order if your lever is cracked or broken.

Refrigerator water inlet tube with bearing assembly. Connects water supply to ice maker or dispenser. Replace if tube is cracked, leaking, or bearing worn.

Official service data sheet with wiring diagrams and diagnostic references. Replace missing or damaged technical documentation for your appliance.

This replacement freezer door restores a sealed, insulated closure and the exterior appearance of the freezer compartment. It installs in place of a damaged or dented door to help maintain proper cooling and prevent frost buildup. What it does:

• Replaces a cracked, dented, or damaged freezer door to restore proper closure and insulation
• Helps maintain the internal temperature by providing a tight seal when aligned correctly
• Prevents cold air loss that can lead to frost buildup and reduced efficiency
• Restores the cabinet's exterior appearance for a clean, finished look

• Disconnect power to the appliance before starting any repair
• Door assemblies are often heavy and awkward—use two people to avoid injury and prevent damage
• Keep original fasteners and gaskets unless the replacement explicitly includes them
• Check door alignment and latch/hinge operation after installation