Kenmore Refrigerator 253.79954704 (25379954704, 253 79954704) Parts

Secures moving components and provides a stable pivot surface in your refrigerator. Replace when worn, broken, or causing looseness and poor alignment.

This micro switch detects door or lid position and tells the appliance when the door is closed so cycles can start or safety interlocks stay engaged. It restores reliable door sensing and helps prevent operation with the door open. What it does:

• Acts as a position sensor that completes or breaks the control circuit when the door/lid is closed or opened
• Keeps the appliance from starting or continuing a cycle if the door is open (safety interlock)
• Common symptom fix: appliance won't start, stops mid-cycle, or shows door-related error codes
• Small electrical switch designed to mount at the door latch or frame and connect to the appliance wiring harness

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing panels, trim, or the door latch assembly; keep track of screws and fasteners
• Observe wiring orientation and connector positions; replace exactly as removed or tag wires

A replacement starter kit used to restore reliable starting operation in compatible Frigidaire appliances. Replaces the original starter components so the appliance can more consistently begin motor/compressor cycles. What it does

• Provides the starter components needed to engage the motor or compressor during power-up.
• Helps resolve symptoms like failure to start, intermittent starts, or humming without run.
• Restores normal starting sequence when starter components are worn or failed.
• Works as a direct-replacement kit for the OEM starter assembly where specified.

• For experienced DIYers only; disconnect power before servicing.
• Follow OEM service instructions for correct routing, mounting, and electrical connections.
• Inspect related components (capacitor, relay, motor) for damage before installation.

Replacement butter dish for refrigerator door dairy compartment. Restores secure storage when original is cracked, broken, or missing. Fits top-mount models.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Bisque plug insert for refrigerator door hinge bearing hole. Replaces missing, cracked, or damaged plugs. Covers hinge pin opening for clean finish.

Secures and organizes wiring harnesses in your refrigerator. Replace if broken, cracked, or wires are loose. Confirm fit with your model number.

Foam insulation block that fills gaps inside the refrigerator cabinet to reduce heat transfer. Replaces damaged, compressed, or missing insulation.

Replaces broken or missing can dispenser for refrigerator door or shelf. Holds and organizes canned beverages. Snaps or hooks into place for neat storage.

Refrigerator not cooling or running constantly? A faulty condenser coil prevents heat release. This repair requires moderate skill and 1-2 hours to complete.

Ice maker not shutting off or making too much ice? A worn lever arm prevents proper shutoff. Simple replacement takes under an hour to restore function.

This ice ejector is the plastic arm that pushes cubes out of the ice maker mold and into the ice bin, restoring proper ice ejection and dispenser function. It's a direct-replacement component for affected ice maker assemblies. What it does:

• Physically strips and pushes formed ice cubes from the mold into the bin or dispenser
• Helps restore normal ice dispensing when cubes remain stuck in the mold
• Works with the ice maker's motor/gear train to time ejection during the harvest cycle
• Commonly replaced when the ejector is broken, cracked, or worn and no longer contacts cubes

• One ice ejector (ejector arm)

• Disconnect power to the refrigerator before starting any repairs
• Remove the ice maker/cover or access panel as required to reach the ejector
• Inspect related components (drive gear, motor, and mounting pins) for wear while replacing the ejector
• After installation, run a test harvest/dispense cycle to correct operation

Replaces your refrigerator's ice maker cover if cracked, broken, or missing. This protective cap installs on the ice maker assembly in your freezer.

Replaces a broken or worn refrigerator door stop that limits door travel. Prevents over-rotation damage to hinges and cabinet. Restores smooth closing.

Nameplate label for freezers and refrigerators. Mounts on exterior cabinet to display model information. Replace if faded, peeling, or missing.