Kenmore Range 362.62020301 (36262020301, 362 62020301) Parts

This oven thermostat uses a capillary sensing bulb to monitor cavity heat and cycle the heating system to maintain your set temperature. Replacing a worn thermostat helps restore more accurate baking and steadier oven performance.

• Monitors oven temperature via a remote capillary sensor bulb
• Opens and closes internal contacts to regulate heat to the setpoint
• Helps resolve: oven not reaching temperature or running too hot
• Also helps with temperature swings, long preheat, or oven not shutting off when the control is turned off

• Disconnect power and shut off gas supply before servicing; allow the oven to cool completely
• Handle the capillary bulb carefully; do not kink or sharply bend it, and route it exactly as originally installed
• Transfer the original knob and any mounting hardware/brackets as needed
• If gas fittings were disturbed, leak-test connections per manufacturer instructions; verify temperature with an oven thermometer and adjust per service guidelines if applicable

Natural gas orifice spud.

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This spacer fits between mating parts in select GE cooking appliances to set correct clearance and alignment. Replacing a worn or missing spacer helps secure the assembly and prevents rubbing or damage to adjacent surfaces during use.

• Maintains proper spacing so hardware tightens squarely and components sit evenly
• Helps prevent metal-to-metal contact that can cause noise, wear, or surface damage
• If missing, broken, or deformed, you may notice looseness, misalignment, rattling, or scraping
• Restores original fit and finish when replaced

• Disconnect power; if applicable, shut off gas. Allow the appliance to cool completely
• Support the part being unfastened (such as a door, handle, or trim) to avoid strain on panels or glass
• Install the spacer in the same location/orientation as the original and reuse existing hardware if serviceable
• Tighten screws evenly; do not overtighten against glass or enameled surfaces

This broiler pan rack is the slotted grid that rests over the broiler pan, supporting food while drippings drain into the pan during broiling. Replace a worn or missing rack to restore safe, consistent broiling results.

• Supports food above the broiler pan so fat and juices drain away while broiling
• Provides proper spacing to the heat source for searing and even browning
• Replaces a rusted, chipped, warped, or missing broiler grid
• Signs of wear can include flaking finish, bent wires, wobbling food, or uneven broiling

• Allow the oven to cool completely before handling; wear heat-resistant gloves
• Set the rack into the matching broiler pan with the slotted surface facing up; verify a stable fit
• Position the assembled pan and rack as directed in your model's use and care guide

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

Location: Left front.

Size: 8 - 32 inch.

Size: 8-18 x 1/2 inch.

This is the screw that secures the burner valve to the appliance, keeping the valve and associated controls fastened for reliable operation. Replaces a worn or missing mounting fastener to restore proper valve alignment and support. What it does:

• Secures the burner valve assembly to the appliance frame or manifold
• Keeps valve position stable to help maintain reliable burner operation
• Helps prevent movement that can cause loose connections or intermittent function
• Used when original screw is stripped, missing, or corroded

• One burner valve mounting screw

• Turn off power and gas supply to the appliance before starting any repair
• Use the correct size driver and avoid over-tightening to prevent stripping the screw or damaging the valve
• Confirm valve and surrounding components are properly aligned before final tightening

Location: Left rear.

This gas burner grate supports cookware on a gas cooktop, restoring stable, level support for safer, more consistent cooking. It replaces a cracked, warped or missing grate so pots and pans sit securely over the burner. What it does:

• Provides a stable surface for cookware so pans sit level over the flame.
• Helps maintain consistent heat contact for more even cooking.
• Replaces broken, chipped, warped or missing grates that cause wobbling or uneven heating.
• Designed to fit the designated cooktop burner location for correct alignment.

• Allow the cooktop to cool and turn all controls to OFF before replacing the grate.
• Remove the old grate and set the new grate into position—no tools are typically required.
• Inspect surrounding burner caps and ignitors; do not operate burners if any components are damaged.
• If you smell gas or suspect a leak, shut off the gas supply.

Package of 12

Bisque