Kenmore Range 362.70251606 (36270251606, 362 70251606) Parts

Package of 12

This is a right-side guide support that secures and aligns a sliding component so drawers or shelves operate smoothly and stay on track. Replaces a worn or broken guide support to restore proper movement and seating. What it does:

• Holds the right-side guide rail or track in place so the drawer or shelf slides evenly
• Prevents the drawer or shelf from sagging, binding, or falling off the track
• Restores proper alignment when the original guide is cracked, broken, or worn
• Works with the existing rail, clips, and mounting hardware to maintain smooth travel

• Disconnect power or unplug the appliance before accessing internal components
• Access may require removing the drawer, shelf, or front panel—use basic hand tools
• Inspect related clips, rails, and fasteners and replace any damaged pieces for best results

This oven felt seal fits around the door perimeter to cushion the door and help reduce heat loss. It restores the intended door clearance and soft contact between the oven door and frame for safer, quieter operation. What it does:

• Cushions the oven door edge to prevent metal-on-metal contact and reduce rattling
• Helps limit heat and smoke from escaping the oven cavity when the door closes
• Restores proper door clearance to prevent scraping or uneven sealing
• Commonly replaced when felt is worn, compressed, torn, or missing

• One oven felt seal as shown

• High-level replacement; remove the oven door or open hinge per your service manual before replacing the seal
• Work with the oven powered off and fully cooled; disconnect power for safety
• Press the felt into the channel or adhesive area; ensure even fit around the full perimeter

This left end cap is a direct-replacement trim piece that restores the finished edge and secure fit of the appliance door or panel. It helps maintain appearance and keeps adjoining trim and seals in place. What it does

• Covers and protects the exposed end of a door or trim piece to prevent sharp edges and wear
• Secures adjacent trim or retainer pieces so gaskets and panels stay aligned
• Stops drafts and reduces the chance of debris getting behind trim
• Common symptom: end cap cracked, loose, or missing causing visible gap or loose trim

• One left end cap

• Basic hand tools typically required; keep fasteners from the original part for reassembly
• Remove surrounding trim or door panel carefully to avoid damaging clips or gaskets
• Inspect adjacent trim and seals while installing; replace any damaged clips or screws as needed
• If work requires removing electrical panels, disconnect power first and follow manufacturer safety instructions

Includes 12 screws.

This replacement panel broiler restores the oven's internal broiler surface so heat reflects properly for consistent top-heat cooking and protects internal components from direct flame and spills. Fits the oven broil cavity where the broil element mounts. What it does:

• Provides the mounting and protective surface for the broil element and helps reflect broil heat across food
• Restores even browning and searing when a damaged or warped panel causes uneven broiling
• Protects internal oven walls and wiring from grease, drips and direct flame contact
• Helps reduce smoke and flare-ups caused by burned-on residue on a damaged panel

• One replacement inner broiler panel

• Disconnect power to the appliance before servicing to avoid shock hazard
• Basic hand tools are typically required; handle edges carefully — panel may have sharp metal edges
• Clean surrounding area and broil element before installation; replace only with the exact part number shown

This insulated wire retainer secures wiring and wiring harnesses inside the appliance to prevent rubbing, chafing, and accidental contact. It helps keep wires routed and protected for safer, more reliable operation. What it does:

• Clips wiring or harness to chassis mounting points to hold wires in place
• Prevents wires from contacting sharp edges or moving parts that can cause wear
• Reduces risk of shorts or intermittent connections caused by chafed insulation
• Keeps wiring neatly routed for easier service and longer component life

• Disconnect power to the appliance before servicing.
• Locate the damaged or missing retainer on the appliance frame or harness mounting tab.
• Route the wire or harness into the retainer and press until the retainer snaps into place; no special tools are typically required.
• Replace any wiring with damaged insulation and secure fit before restoring power.

Includes 12 screws.

Anti-tip kit.

Location: Right front.

This white broiler handle replaces a cracked, loose, or missing handle so you can open and close the oven broiler or broiler drawer smoothly. Durable plastic construction restores safe, reliable access to the broiler compartment. What it does:

• Provides a secure grip to open and close the broiler or broiler drawer
• Replaces worn, broken, or chipped handles that are hard to use
• Helps prevent accidental slippage when accessing the broiler area
• Restores normal operation and appearance to the oven front

• One white broiler handle

• Turn off power to the appliance before beginning any work
• Installation typically requires removing the broiler drawer or access panel and fastening the handle with the original screws or clips
• Handle broken hardware may require replacement fasteners; confirm what's needed before starting
• Wear gloves to avoid cuts from sharp sheet metal edges during installation

This replacement drawer panel restores the front trim of the appliance drawer for a clean, finished appearance and proper fit. It replaces a damaged, dented, or worn drawer front so the drawer closes and looks like new. What it does:

• Replaces the external front surface of the drawer to restore appearance and alignment
• Helps the drawer close evenly and prevents gaps that allow items to catch
• Addresses visible damage such as dents, scratches, or paint wear on the drawer front
• Works with existing drawer hardware; does not include internal drawer bin parts

• One replacement drawer panel

• Handle part carefully to avoid surface scratches
• Power off and empty drawer before starting; remove any clips or screws securing the old panel
• Reuse original fasteners and brackets unless damaged

Location: Right rear.