Kenmore Range 362.75322002 (36275322002, 362 75322002) Parts

Genuine Ge part

Range Oven Door Hinge Pin

By: Ge

Part Number: WB14K5

Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.

Genuine Ge part

Front Drawer Panel

5.0 (1)

By: Ge

Part Number: WB36K10033

Color: White

Do-It-Yourself Stories from Customers like You The drawer of my oven had many scratches and i wanted to replace it Elizabeth W. • Hood River , OR • April 02, 2015

I contacted Appliance Parts Pros, the person who answered the phone was very helpful and we ordered the correct part for my oven. The part arrived very quickly and in perfect shape. I installed it this morning in about a half an hour or less. Because the person who helped me at Appliance Parts Pros was so knowledgeable and helpful, I now have an oven that looks brand new! Thank you! Read more

Genuine Ge part

Panel, Oven Bottom

5.0 (6)

By: Ge

Part Number: WB53K35

Do-It-Yourself Stories from Customers like You The panel on the oven bottom was pitted and needed to be replaced Kenneth W. • Buffalo , MN • November 29, 2014

Simple as can be. Took 2 screws out, pulled out the old panel, and put the new one in. Done in five mintures Read more

Genuine Ge part

Support Rivet

By: Ge

Part Number: WB10K14

Left hand side

Genuine Ge part

Top Burner Igniter

4.0 (1)

By: Ge

Part Number: WB13K10003

Electrode

Do-It-Yourself Stories from Customers like You Ignitor discolored and hard to lite burner had to start using lighter William S. • Bel Air , MD • November 28, 2016

Watch U-tube video but wrong for my stove Disconnected burner from top which I did not have to do All I had to do was pull ignitor straight up (wire would come with it and disconnect wire from ceramic then push back into place Because I disconnected via video insturction turned a five minute job into a 30 minute job Burner ignites now Wife happy (best) Read more

Genuine Ge part

Broil Burner

5.0 (2)

By: Ge

Part Number: WB16K10004

Do-It-Yourself Stories from Customers like You Not working ignitor. Daryl V. • Sacramento , CA • January 02, 2021

Replaced broil burner and ignitor. Read more

Genuine Ge part

Regulator, Pressure

4.7 (6)

By: Ge

Part Number: WB19K10001

Do-It-Yourself Stories from Customers like You Regulator was bad Charles S. • Phoenix , AZ • July 24, 2017

Changed it out Read more

Genuine Ge part

Switch Latch

By: Ge

Part Number: WB24K10010

Genuine Ge part

Control

5.0 (2)

By: Ge

Part Number: WB27K10141

Do-It-Yourself Stories from Customers like You Sensor Daniel P. • Riverton , WY • February 14, 2015

ORDERD sensor PART AND IT CAME VERY FAST,I ORDERED A CONTROL BOARD ALSO AND IT CAME FAST AND IN BUBBLE RAP. VERY GOOD SERVICE A+ Read more

Genuine Ge part

Elbow Hi-Broil

By: Ge

Part Number: WB28K10018

Genuine Ge part

Tube Manifold Supply

4.5 (2)

By: Ge

Part Number: WB28K10021

Do-It-Yourself Stories from Customers like You Tube manifold from gas supply to stovetop broke Rick W. • Three Rivers , MI • November 15, 2014

I had to open up the side panel of the range and pull up the stove top. Unscrewed both ends of the old tube and pulled it out. Installed new tube and screwed the top into place. Had to do a little bending of the tube to get it to fit. The "supply" end was a little shorter than the original, and the bends were a little different, but not too bad that I couldn't make it work. Screwed on the bottom end of the tube. Read more

Genuine Ge part

Orifice Spud

5.0 (4)

By: Ge

Part Number: WB28K10022

Natural gas. Med 1.50mm

Do-It-Yourself Stories from Customers like You Propane to natural gas conversion on range and dryer Vincent P. • Howell , NJ • October 09, 2014

Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time. Read more