Kenmore Range 362.75497000 (36275497000, 362 75497000) Parts
Genuine Ge part
By: Ge
Part Number: WB49K2
Do-It-Yourself Stories from Customers like You
Burned on pans Cheryl R. • Piney Creek , NC • October 30, 2015
New pans
Read more
More
Genuine Ge part
By: Ge
Part Number: WB10K13
This support rivet securely fastens internal components within your range or oven structure. It provides structural stability for mounting brackets and panels inside the appliance. Replace this rivet if you notice loose parts rattling inside your oven or range components shifting during use.
More
Genuine Ge part
By: Ge
Part Number: WB2K11
Genuine Ge part
By: Ge
Part Number: WB2X1082
This retainer secures the oven door hinges in place and is located at the bottom corners of the oven door frame. Replace if the oven door sags, won't stay closed properly, or if the hinges appear loose or misaligned.
Do-It-Yourself Stories from Customers like You
Broken door hinge. Shari W. • Evansville , IN • February 07, 2018
By replacing the hinge.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB14K5
Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.
More
Genuine Ge part
By: Ge
Part Number: WB24X415
Color: Black
Do-It-Yourself Stories from Customers like You
Old worn parts Billy S. • Newport News , VA • February 26, 2016
Easy removal of worn parts and easy installation of new parts.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB53K35
Do-It-Yourself Stories from Customers like You
The panel on the oven bottom was pitted and needed to be replaced Kenneth W. • Buffalo , MN • November 29, 2014
Simple as can be. Took 2 screws out, pulled out the old panel, and put the new one in. Done in five mintures
Read more
More
Genuine Ge part
By: Ge
Part Number: WB03K10021
Genuine Ge part
By: Ge
Part Number: WB10K14
Genuine Ge part
By: Ge
Part Number: WB13K10003
Electrode
Do-It-Yourself Stories from Customers like You
Ignitor discolored and hard to lite burner had to start using lighter William S. • Bel Air , MD • November 28, 2016
Watch U-tube video but wrong for my stove
Disconnected burner from top which I did not have to do
All I had to do was pull ignitor straight up (wire would come with it and disconnect wire from ceramic then push back into place
Because I disconnected via video insturction turned a five minute job into a 30 minute job
Burner ignites now
Wife happy (best)
Read more
More
Genuine Ge part
By: Ge
Part Number: WB16K10004
Do-It-Yourself Stories from Customers like You
Broiler taking too long to light and burner metal burning through Paul H. • Bixby , OK • October 31, 2018
Replaced the Broil Burner and Oven Igniter. Removed the door (lifts out easily). Moved out oven to access electrical socket and gas line. Unplugged electricity. Shut off gas. Disconnected gas line. Moved out oven to access back panel.
Disconnected Igniter clip. Removed the small access plate. Unscrewed holding screws from broil burner and removed the old Burner and Igniter.
Put the new burner and Igniter together and reversed the process.
So far so good. Was a $70 repair or a $1000 new...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB19K10001
Do-It-Yourself Stories from Customers like You
Regulator was bad Charles S. • Phoenix , AZ • July 24, 2017
Changed it out
Read more
More
Genuine Ge part
By: Ge
Part Number: WB24K10010
Genuine Ge part
By: Ge
Part Number: WB27K10142
Due to manufacturer changes, must also replace knob part number WB03K10116.
Do-It-Yourself Stories from Customers like You
Not controlling temperature properly Scott W. • Torrance , CA • May 10, 2016
Replaced Control Board. The plastic overlay was difficult to replace as there were no indexing tabs on the control module. I had to "eyeball it"!.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB28K10018
Genuine Ge part
By: Ge
Part Number: WB28K10021
Do-It-Yourself Stories from Customers like You
Tube manifold from gas supply to stovetop broke Rick W. • Three Rivers , MI • November 15, 2014
I had to open up the side panel of the range and pull up the stove top. Unscrewed both ends of the old tube and pulled it out. Installed new tube and screwed the top into place. Had to do a little bending of the tube to get it to fit. The "supply" end was a little shorter than the original, and the bends were a little different, but not too bad that I couldn't make it work. Screwed on the bottom end of the tube.
Read more
More