Kenmore Refrigerator 363.58252890 (36358252890, 363 58252890) Parts
Genuine Ge part
By: Ge
Part Number: WR38X10066
$15.96
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR38X10067
$13.81
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1741
This breaker strip trim installs along the freezer section edge of your refrigerator. Replace if cracked, broken, or missing to restore appearance.
More
$49.07
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1742
Breaker strip trim for top freezer compartment door. Replace if cracked, broken, or missing to restore door seal and cabinet finish appearance.
More
$12.61
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1743
Bottom freezer door breaker strip for refrigerators. Seals the gap between door sections. Replace if cracked, broken, or missing for proper fit.
More
$46.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1744
$31.41
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1745
$18.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR40X1746
$17.98
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WZ6X136
$9.74
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WR60X30349
The Evaporator Fan Motor Kit is an OEM part compatible with GE refrigerators. It is a critical component responsible for circulating air and maintaining proper airflow within the refrigerator's evaporator system, ensuring efficient cooling and temperature regulation. It features a shaft that measures 3/8 of an inch and two right-side terminals. Notably, the motor no longer comes with harness wires, which must be obtained separately for installation.
Symptoms of a faulty evaporator fan motor include:
- Inconsistent or inadequate cooling in the refrigerator or freezer compartments
- Warm spots or temperature fluctuations within the refrigerator
- Excessive frost buildup or ice accumulation in the freezer
Causes of a bad evaporator fan motor can include wear and tear over time, electrical issues or short circuits, or physical damage from foreign objects or improper maintenance.
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models.
Do-It-Yourself Stories from Customers like You
The refrigerator would not cool nor freeze! Tom C. • Kenmore , WA • October 31, 2015
I called AppliancePartsPros.com and they helped me diagnose the problem for this very nice, and well designed refrigerator, that I wanted to keep rather than recycle at the local scrap yard. It turns out that all it needed was a small electric fan (i.e., evaporator fan) to circulate the air from the freezer coils throughout the refrigerator [all other major components were good]. It was really easy to locate the motor and fan and replace it. I saved hundreds of $$$. I really appreciated the...
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X8474
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
This part fixes the following symptoms
-
Leaking
-
Ice maker not making ice
See more...
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
Genuine Ge part
By: Ge
Part Number: WR17X3089
Links the dispenser solenoid to the ice chute door in your refrigerator. Replace if the crank is broken, cracked, or worn, preventing proper closure.
Do-It-Yourself Stories from Customers like You
Ice build up on front of icemaker Brian H. • Mccalla , AL • August 06, 2016
REPLACED DISPENSER CRANK ARM, SPRING, FLAPPER FOR DISPENSER. THE REPAIR WAS VERY SIMPLE WITH NO PROBLEMS AT ALL.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X7391
The Fan Blade Grommet is an OEM replacement part for GE brand refrigerators. Located behind the evaporator fan blade where its central shaft passes through, this rubber sealing piece creates a protective barrier isolating the fan assembly.
Causes of a potentially problematic fan blade grommet include cracks or deterioration that develop from continuous vibration and impacts over extended use. Exposure to temperature fluctuations can also cause the rubber to harden and lose elasticity.
Symptoms of a faulty fan blade grommet include:
- Airflow obstructions within the duct
- Noisy vibrations from the fan assembly
- Rubber debris collecting on components
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore model refrigerators.
Do-It-Yourself Stories from Customers like You
I had a very noisy evaporator fan in older GE refrigerator top freezer Richard B. • Casa Grande , AZ • December 06, 2019
Replaced the evaporator fan motor, fan blade, and two rubber grommets. I was careful to mark screws and bolts with sticky notes to ensure getting them back in the right place. I had all the new parts ready before I started the job because I did not have an extra freezer for my food and I wanted to do this quickly and only once. New parts went in well, Took a while to install the ring for the new fan blade using my long nose pliers. I would have saved time if I had the special ring spreader...
Read more
More
Genuine Ge part
By: Ge
Part Number: WR02X11561
Do-It-Yourself Stories from Customers like You
Ice maker stopped working. Jorge J. • Winter Garden , FL • April 05, 2019
Replaced Ice maker very easy.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X4550
The Drive Cup is an OEM part for GE refrigerators. This part engages with other parts to drive the ice out of the molds and into the storage bin.
Causes of Drive Cup failure can range from physical wear and tear from regular use, which may lead to cracks or deformities in the part, to accumulation of frost or ice that hinders its movement.
Symptoms of a malfunctioning Drive Cup include:
- The ice maker fails to eject ice properly, leading to clogs or jams within the system.
- Unusual noises during the ice-making cycle, which could indicate that the drive cup is not engaging correctly with other components.
- Decreased efficiency in ice production, as the mechanism struggles to operate smoothly.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
This part fixes the following symptoms
-
Ice maker won't dispense ice
See more...
Do-It-Yourself Stories from Customers like You
The problem was the auger was rusted and it came out on the ice Marie L. • Central Square , NY • August 04, 2017
Ordered new auger and installed it and now we have clean ice for our drinks.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR2X8663
The Ice Door Spring is an OEM part compatible with GE refrigerators. It is responsible for providing tension and support to the ice chute door, allowing it to open and close smoothly. When you activate the ice dispenser, the spring helps to release the door and allow the ice to pass through. After dispensing, the spring assists in closing the door to prevent cold air leakage and maintain the desired temperature inside the refrigerator.
You should replace the ice door spring if it loses tension or breaks, which can happen due to regular wear and tear, frequent use, or accidental damage. A faulty spring can lead to issues with the ice dispenser's operation and overall efficiency.
Symptoms of a bad ice door spring may include:
- Difficulty in opening or closing the ice chute door
- Ice dispensing issues, such as the door not opening when the dispenser is activated
- Cold air leakage from the ice chute area
- Ice buildup on the front of the icemaker
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Ice dispenser door not closing tightly; frost build up in ice chute; mold growing behind ice and water mechanism Terrance A. • Arleta , CA • March 21, 2017
The ice dispenser door was not closing tightly. As a result, there was frost build up in the ice chute, which also was allowing ambient air and temperature into the freezer compartment. Upon further inspection, there was black “schmutz” on the ice door, and the rubber ice funnel and deflector parts were deteriorating. Because the door was not closing tightly, I also assumed that the door-closing spring was week. The parts I ordered were: ice door assembly, ice funnel, ice deflector, spring and...
Read more
More